Free sample questions
12 original questions from the app's free slice. Tap an answer to see the explanation.
AM.I.A.K1 1/12
Using electron flow theory, in which direction does current move through the external circuit connected to a battery?
Electrons are repelled by the negative terminal and attracted to the positive one, so electron flow runs negative to positive through the load. Positive to negative is conventional flow, the opposite convention. Electrons are not consumed in the load; the same number return to the source. Source: FAA-H-8083-30B, Fundamentals of Electricity and Electronics / Electron theory and current flow
AM.I.A.K1 2/12
While reading a schematic, a technician notes that the arrowhead in a diode symbol points toward the bar. The arrowhead shows the direction of:
Semiconductor symbols were drawn using conventional flow, so the arrow points from anode to cathode in the direction conventional current passes when forward biased. Electrons in that same diode move against the arrow, from cathode to anode. The diode blocks current in the reverse direction, not in the arrow direction. Source: FAA-H-8083-30B, Fundamentals of Electricity and Electronics / Electron theory; semiconductor symbols
AM.I.A.K2 3/12
Why is soft iron normally chosen as the core of an electromagnet such as a relay coil?
Soft iron offers an easy path for flux (high permeability, low reluctance) and retains little residual magnetism, so the relay releases when the coil is de-energized. High retentivity is wanted in permanent magnets, not in a relay core. High reluctance would oppose flux and weaken the magnet. Source: FAA-H-8083-30B, Fundamentals of Electricity and Electronics / Magnetism; permeability and retentivity
AM.I.A.K2 4/12
A technician applies the left-hand rule to a coil, curling the fingers around it in the direction of electron flow. The extended thumb points toward the coil's:
With the left hand and electron flow, the fingers follow electron flow around the turns and the thumb points to the north pole of the coil. The south pole is at the opposite end. The rule locates magnetic polarity, not electrical terminals, so the thumb says nothing about which lead is positive. Source: FAA-H-8083-30B, Fundamentals of Electricity and Electronics / Electromagnetism; left-hand rule for coils
AM.II.A.K1 5/12
Which nondestructive inspection method can reveal only those discontinuities that are open to the surface of the part?
Penetrant works only by seeping into a defect that breaks the surface and bleeding back out into the developer, so a closed internal flaw stays invisible. Eddy current can detect flaws slightly below the surface, and ultrasonic inspection is used for internal discontinuities. Source: FAA-H-8083-30B, Inspection Concepts and Techniques / Liquid penetrant inspection
AM.II.A.K1 6/12
A mechanic must inspect a 2024-T3 aluminum landing gear attach bracket for cracks. Which NDI method is NOT usable on this part?
Magnetic particle inspection needs a ferromagnetic material that can be magnetized; aluminum is nonmagnetic, so no leakage field forms at a crack. Eddy current only needs an electrically conductive part, which aluminum is, and penetrant works on any nonporous material. Source: FAA-H-8083-30B, Inspection Concepts and Techniques / Magnetic particle inspection
AM.II.A.K1 7/12
After a fire near an aluminum wing panel, which NDI method can check whether the alloy's heat-treated condition was changed by the heat?
Overheating changes the temper of an aluminum alloy, and that changes its electrical conductivity, which an eddy current conductivity meter can measure and compare to the correct value. Penetrant finds only surface cracks, not a change in temper, and magnetic particle does not work on aluminum. Source: FAA-H-8083-30B, Inspection Concepts and Techniques / Eddy current inspection
AM.II.A.K2 8/12
When an inspector examines a bushing that slides in a fitting, they find particles of the softer metal torn loose and welded onto the harder surface. This damage is called:
Galling is the breakdown of mating surfaces from too much friction during relative motion, with metal from the softer part torn off and welded to the harder one. Burnishing is a polishing of one surface by sliding contact, with no metal removed or displaced, and brinelling is a shallow round dent from a high load. Source: FAA-H-8083-31B, Aircraft Metal Structural Repair / Types of damage and defects
AM.III.A.K1 9/12
In the engine model designation TSIO-520, what does the number 520 indicate?
The number in a reciprocating engine designation is its approximate total displacement in cubic inches, so a TSIO-520 displaces about 520 cu in. Rated horsepower is not part of the designation and must be taken from the type certificate data sheet. Source: FAA-H-8083-32B, Aircraft Engines / Reciprocating engine designations
AM.III.A.K1 10/12
An engine is listed as a GO-480. What does the letter G tell the mechanic about this engine?
In engine designations the G stands for geared: the propeller is driven through a reduction gear so it turns slower than the crankshaft. A supercharged engine is identified by S (as in GSO-480), not by G. Source: FAA-H-8083-32B, Aircraft Engines / Reciprocating engine designations
AM.III.A.K1 11/12
Compared with a radial engine of similar power, why is the horizontally opposed engine favored for most light airplanes?
The opposed engine is compact and flat, so its small frontal area lets it be cowled with little drag, and it has a low weight-to-horsepower ratio. Placing several cylinders on one crankpin is a radial feature, and opposed engines commonly use a wet sump. Source: FAA-H-8083-32B, Aircraft Engines / Opposed-type engines
AM.III.A.K1 12/12
Why are air-cooled in-line engines generally built with no more than about six cylinders?
In an air-cooled in-line engine the rear cylinders sit in the wake of the front ones and receive little cooling air, which limits the practical number of cylinders. Long crankshafts and even firing orders are routine in larger engines, so neither is the limiting factor. Source: FAA-H-8083-32B, Aircraft Engines / In-line engines