A&P formulas with worked examples
The A&P written tests reuse a short list of formulas: Ohm's law (E = I × R) and Watt's law (P = E × I), area and volume, compression ratio, force = pressure × area, work and horsepower, levers, torque wrench extensions, bend allowance, PLANK and moment = weight × arm. Each one is below with a worked example. The formulas come from the FAA Aviation Maintenance Technician Handbooks (General, Airframe, Powerplant) and the Weight and Balance Handbook; the example numbers are invented for practice.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
Which formulas are on which test?
| Formula | ACS area | Test |
|---|---|---|
| Ohm's and Watt's law, series and parallel | AM.I.A, AM.II.K, AM.III.F | AMG, AMA, AMP |
| Area, volume, ratio, torque units | AM.I.H | AMG |
| Force, pressure, work, horsepower, levers, gas law, temperature | AM.I.J | AMG |
| Moment and CG | AM.I.C | AMG |
| Torque wrench extension | AM.I.E | AMG |
| Bend allowance and setback | AM.II.A | AMA |
| Displacement, compression ratio, PLANK | AM.III.A | AMP |
Area codes from FAA-S-ACS-1. The test allows an aviation or simple arithmetic calculator, and the FAA test tips say to read every note on a calculation question (FAA-G-ACS-1, chapter 4).
How do I use Ohm's law and Watt's law?
E = I × R, so I = E ÷ R and R = E ÷ I. Power is P = E × I, which also gives P = I² × R and P = E² ÷ R.
Example 1: a 28-volt circuit with 4 ohms of resistance.
- I = E ÷ R = 28 ÷ 4 = 7 A
- P = E × I = 28 × 7 = 196 W
Example 2: a 70-watt lamp on a 14-volt bus. What current does it draw?
- I = P ÷ E = 70 ÷ 14 = 5 A
Series and parallel resistance
Series: RT = R₁ + R₂ + …. Parallel: 1/RT = 1/R₁ + 1/R₂ + …, and for two branches RT = (R₁ × R₂) ÷ (R₁ + R₂). A parallel total is always smaller than the smallest branch.
Example 3: a 4 Ω resistor in series with a 6 Ω and a 12 Ω in parallel, on 24 V.
- Parallel pair = (6 × 12) ÷ (6 + 12) = 72 ÷ 18 = 4 Ω
- Total = 4 + 4 = 8 Ω
- Current = 24 ÷ 8 = 3 A, and the drop across the 4 Ω resistor is 3 × 4 = 12 V
- Each parallel branch sees the other 12 V: 2 A through 6 Ω and 1 A through 12 Ω, which add back to 3 A (Kirchhoff's current law)
Practice it live: series-parallel workup and bus load workup.
What area and volume formulas do I need?
| Shape | Formula |
|---|---|
| Rectangle | A = length × width |
| Triangle | A = ½ × base × height |
| Trapezoid (tapered wing planform) | A = ½ × (a + b) × height |
| Circle | A = π × r² = 0.7854 × d² |
| Rectangular solid (tank) | V = length × width × height |
| Cylinder | V = π × r² × height |
One US gallon is 231 cubic inches. The FAA weight and balance handbook uses 6 lb per gallon for avgas in its examples, so 40 gallons weigh 240 lb (FAA-H-8083-1B). See the tank volume workup.
How do I find displacement and compression ratio?
Displacement is piston area × stroke × number of cylinders. Compression ratio is the total cylinder volume with the piston at bottom center divided by the clearance volume with it at top center.
Example 4: a 6-cylinder engine with a 5.125 in bore, 4.375 in stroke and 12.9 cubic inches of clearance volume per cylinder.
- Piston area = π × (5.125 ÷ 2)² = 20.629 sq in
- Displacement per cylinder = 20.629 × 4.375 = 90.3 cu in
- Total displacement = 90.3 × 6 = 542 cu in
- Compression ratio = (90.3 + 12.9) ÷ 12.9 = 8.0 : 1
The usual wrong answer uses the diameter as the radius, which makes the area four times too big. Practice in the displacement workup.
How is indicated horsepower calculated with PLANK?
IHP = (P × L × A × N × K) ÷ 33,000, where P is indicated mean effective pressure in psi, L the stroke in feet, A the piston area in square inches, N the power strokes per minute per cylinder (rpm ÷ 2 for a four-stroke engine) and K the number of cylinders (FAA-H-8083-32B).
Example 5: the engine above at 2450 rpm with an IMEP of 150 psi.
- L = 4.375 ÷ 12 = 0.3646 ft
- N = 2450 ÷ 2 = 1225 power strokes per minute
- IHP = (150 × 0.3646 × 20.629 × 1225 × 6) ÷ 33,000 = 251 hp
Two traps: the stroke must be in feet, and N is half the rpm. The PLANK workup shows both.
How do force, pressure and area relate?
Force = pressure × area. On the rod side of an actuator, use the piston area minus the rod area.
Example 6: 1,500 psi acting on a piston with 2 square inches of area.
- F = 1,500 × 2 = 3,000 lb
- If the rod takes 0.5 sq in, the rod side gets 1,500 × 1.5 = 2,250 lb
Workup: actuator force.
How do I work out work, power and horsepower?
Work = force × distance (foot-pounds) and power = work ÷ time. One horsepower is 33,000 ft-lb per minute or 550 ft-lb per second (FAA-H-8083-30B).
Example 7: a hoist lifts a 1,650 lb engine 20 ft in 2 seconds.
- Work = 1,650 × 20 = 33,000 ft-lb
- Power = 33,000 ÷ 2 = 16,500 ft-lb per second
- Horsepower = 16,500 ÷ 550 = 30 hp
How does a lever's mechanical advantage work?
MA = effort arm ÷ resistance arm, and effort × effort arm = resistance × resistance arm.
Example 8: a 100 lb load 6 inches from the fulcrum, with the effort applied 30 inches away.
- MA = 30 ÷ 6 = 5
- Effort = 100 ÷ 5 = 20 lb
How do the gas law and temperature conversions work?
°F = °C × 9/5 + 32, °C = (°F − 32) × 5/9, °R = °F + 460, K = °C + 273. The general gas law is P₁V₁/T₁ = P₂V₂/T₂ with absolute pressure and absolute temperature.
Example 9: an accumulator precharged to 1,000 psi gauge at 70 °F cools to 20 °F. Volume is constant.
- P₁ = 1,000 + 14.7 = 1,014.7 psia; T₁ = 70 + 460 = 530 °R; T₂ = 20 + 460 = 480 °R
- P₂ = 1,014.7 × 480 ÷ 530 = 919.0 psia
- Gauge pressure = 919.0 − 14.7 = 904 psi
Using Fahrenheit directly (20 ÷ 70) gives a wildly wrong answer, which is a common distractor. See the gas law workup.
What does a torque wrench read with an extension?
Inch-pounds ÷ 12 = foot-pounds. When an adapter lengthens the wrench in line with it, set the wrench to TW = TA × L ÷ (L + E), where TA is the torque wanted at the fastener, L the wrench's lever length and E the extension length (FAA-H-8083-30B).
Example 10: 300 in-lb required, a 12 in wrench and a 3 in extension.
- TW = 300 × 12 ÷ (12 + 3) = 3,600 ÷ 15 = 240 in-lb
- In foot-pounds: 240 ÷ 12 = 20.0 ft-lb
The dial reads less than the required torque, because the extension adds leverage. Workup: torque extension.
How do I calculate bend allowance and setback?
BA = (0.01743 × R + 0.0078 × T) × N, where R is the inside bend radius, T the material thickness and N the degrees of bend. Setback is SB = K × (R + T), and K is 1 for a 90° bend (FAA-H-8083-31B).
Example 11: a 90° bend in 0.040 in sheet with a 0.125 in bend radius.
- BA = (0.01743 × 0.125 + 0.0078 × 0.040) × 90 = 0.224 in
- SB = 1 × (0.125 + 0.040) = 0.165 in
- Flat length = mold-line flange lengths − 2 × setback + bend allowance
Workups: bend allowance and rivet layout.
How do I compute a CG?
Moment = weight × arm and CG = total moment ÷ total weight, with arms measured from the datum (FAA-H-8083-1B).
Example 12: an empty airplane of 1,500 lb at 80 in, 340 lb of occupants at 85 in and 240 lb of fuel at 95 in.
- Moments: 120,000, 28,900, 22,800 lb-in
- Total weight = 2,080 lb; total moment = 171,700 lb-in
- CG = 171,700 ÷ 2,080 = 82.55 in aft of datum
More in Weight and balance for the A&P test and the loaded CG workup.
Free mini quiz: 6 practice questions
Six questions from the calculation-heavy areas: math, physics, electricity, weight and balance, sheet metal and reciprocating engines. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.H.K3 g3-068
A standard hex nut is shaped as a regular hexagon. What is each of its interior angles?
- 60 degrees
- 120 degrees
- 720 degrees
Show answer
Answer: B. The interior angles of a polygon total (n - 2) x 180; for six sides, 4 x 180 = 720 degrees, and each of the six equal angles is 720 / 6 = 120 degrees. The 60 degrees is the central angle (360 / 6), and 720 degrees is the sum, not one angle.
Source: FAA-H-8083-30B, Mathematics in Aviation Maintenance / Geometric terms; polygons
AM.I.J.K3 g4-046
A block and tackle has four rope segments supporting the movable block that holds a 360-lb engine. Ignoring friction, what pull is needed, and how much rope must be pulled to raise the engine 2 ft?
- 90 lb, pulling 8 ft of rope
- 90 lb, pulling 2 ft of rope
- 180 lb, pulling 4 ft of rope
Show answer
Answer: A. Four supporting segments give a mechanical advantage of 4: 360 / 4 = 90 lb. Each segment must shorten by 2 ft, so 4 x 2 = 8 ft of rope is pulled. Less force always costs more distance, so 90 lb with only 2 ft of rope is impossible.
Source: FAA-H-8083-30B, Physics for Aviation
AM.I.A.K3 g1-007
A 200 kilohm resistor is in series with an uncharged 25 microfarad capacitor across a 28 V DC source. About how long will the capacitor take to become essentially fully charged?
- 25 seconds
- 5 seconds
- 3.2 seconds
Show answer
Answer: A. One time constant is R x C = 200,000 ohms x 0.000025 F = 5 s, and a capacitor is considered fully charged after about five time constants: 5 x 5 s = 25 s. At 5 s (one time constant) it has reached only about 63 percent of the source voltage. 3.2 s is 63 percent of one time constant and has no meaning here.
Source: FAA-H-8083-30B, Fundamentals of Electricity and Electronics / Capacitance; RC time constant
AM.I.C.K1 g2-003
An older airplane's type certificate data sheet lists an empty-weight CG range. If the airplane's empty-weight CG falls inside that range, what does it mean?
- Any legal loading per the placards will keep the loaded CG within limits
- The airplane does not need to be weighed again after any later alteration
- The empty CG is acceptable, but forward and aft adverse checks are still required
Show answer
Answer: A. Per FAA-H-8083-30B, the empty-weight CG range is set so that if the empty CG falls within it, no loading permitted by the placards and limitations (occupants, fuel, baggage) can move the loaded CG outside the approved envelope, so forward and aft adverse-loading checks are not needed. It does not waive reweighing or recomputing weight and balance after an alteration that changes the empty weight or CG.
Source: FAA-H-8083-30B, Aircraft Weight and Balance / Empty-weight CG range
AM.II.A.K3 a1-009
A repair drawing calls for 7075-T6 sheet. What is the principal alloying element in this alloy?
- Copper
- Magnesium
- Zinc
Show answer
Answer: C. In the four-digit aluminum system, the 7xxx series uses zinc as its main alloying element, which gives 7075 its very high strength. Copper is the main element of the 2xxx series (such as 2024), and magnesium is the main element of the 5xxx series.
Source: FAA-H-8083-30B, Materials and Processes / Aluminum alloy designations
AM.III.A.K2 p1-010
Why is the spark timed to occur before the piston reaches top center on the compression stroke?
- So combustion is complete before the piston reaches top center
- Burning takes time, so peak pressure develops just after top center
- Early ignition lowers combustion temperature and prevents detonation
Show answer
Answer: B. The charge burns progressively rather than instantly, so it is ignited early enough that maximum pressure builds just after top center, when it can push the piston down. Finishing combustion before top center would push against the rising piston, and over-advanced timing tends to cause detonation, not prevent it.
Source: FAA-H-8083-32B, Aircraft Engines / Four-stroke cycle / ignition event
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Where do the test figures come from?
- Figures, charts and tables come from the testing supplement (FAA-CT-8080-4G) or are shown on screen. Learn the formulas so you are not hunting for them during the test.
- What calculator can I bring?
- An aviation calculator or a simple arithmetic calculator, if the proctor can see its memory is cleared (FAA-G-ACS-1, chapter 4).
- Are these the only formulas?
- They are the ones that come up most. The ACS also lists binary numbers, powers and roots, and rounding in mathematics (AM.I.H).
Sources
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General. FAA. Used to write the practice items 2026-11-14.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-14.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-14.
- FAA-H-8083-1B, Aircraft Weight and Balance Handbook (2016). FAA. Read 2026-11-14.
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.