The A&P oral and practical (O&P) test
After you pass the written tests, a Designated Mechanic Examiner (DME) gives the oral and practical test for each rating, built by the FAA's Mechanic Test Generator from the ACS. The oral part retests the ACS codes you missed on your written test reports, with no references allowed; the practical part is hands-on projects, where you may use the references the examiner provides (FAA-G-ACS-1, chapter 6). DMEs set their own fee, which you agree on before the test.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-11); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
How do I book the O&P?
Find a DME with the FAA's designee locator or through your local Flight Standards office, and contact them directly. Before testing, the DME holds a pre-test interview to set the date, time and place and to look at the codes on your written test reports. The FAA guide says designees "may charge a reasonable fee" that should be agreed before the test (FAA-G-ACS-1, chapter 6). The FAA FAQ says there are no DMEs outside the US (FAA mechanic FAQ).
What do I bring?
- Two identically prepared FAA Forms 8610-2 with original signatures
- Your passing written test reports (unless your school is testing you early under 14 CFR 65.80)
- Current government photo ID with a signature, such as a passport, military ID or driver's license
- Your eligibility document: the Part 147 graduation document, Form 8610-2 signed in Block V by an FAA inspector, or a military certificate of eligibility
Missing documents can delay or end the test (FAA-G-ACS-1, chapter 6).
How do the oral and the practical differ?
| Oral | Practical | |
|---|---|---|
| What is tested | The ACS knowledge elements behind the codes you missed on the written tests. With 100% on a written test you still get a minimum number of random oral questions. | Projects drawn from the ACS skill elements, with questions on the knowledge and risk management tied to each project |
| References | Not allowed | Allowed, but only those the examiner provides (14 CFR, ADs, ACs, manufacturer manuals and similar) |
| Standard | Acceptable knowledge of each retested element | Work to a return-to-service standard where it applies, find and apply the right reference, and work safely; disregard for safety is a failure |
| If you fail | The retest covers the entire section failed (General, Airframe or Powerplant) | The retest covers the failed projects and any subject areas not tested |
Source: FAA-G-ACS-1, chapters 6 and 7. Retest timing follows 14 CFR 65.19: after 30 days, or sooner with a signed statement of additional instruction. Bring every Form 8610-2 marked failed or "not tested" to the retest.
What changed in the 2026 practical test banks?
The FAA rewrote the practical test banks so practical questions line up with the assigned project, the aircraft maintenance manual and advisory circulars, and gave DMEs more room to accept answers based on project details and approved references. The new General bank went live April 20, 2026 and the Airframe bank July 20, 2026; Powerplant is planned for 2027. If your first practical was before the change, your retest uses the earlier content. Examiners were also told to add a liquid penetrant kit for project AM.I.K.S5 by December 2026, and the General project AM.I.L.S1 has you fill in Form 8010-4, Malfunction or Defect Report, on paper or a fillable PDF (ATCA, October 2026).
What happens when I pass?
The DME issues a temporary airman certificate, signed by you and the designee, valid for 120 days while the FAA reviews the file and mails the permanent certificate. Applicants who pass before turning 18 hold their documents until their 18th birthday (FAA-G-ACS-1, chapter 7).
Free mini quiz: 8 practice questions
Eight questions on maintenance records and forms, which come up in both the oral and the practical projects. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.I.K3 g4-008
Under 14 CFR 43.9, a mechanic replacing a fuel strainer gasket does not want to rewrite the whole manual procedure in the logbook. What may the entry contain instead of a full description?
- A reference to FAA-acceptable data, such as the manual section used
- Only the part number of the new gasket and the date it was installed
- Only a statement that the work was done at the owner's request and expense
Show answer
Answer: A. 14 CFR 43.9(a)(1) requires a description of the work or a reference to data acceptable to the Administrator, so citing the applicable maintenance manual section satisfies it. A part number alone does not describe the work performed, and the owner's request has no bearing on the record.
Source: 14 CFR 43.9
AM.I.I.K3 g4-009
A private pilot replaces the oil filter element on the airplane the pilot owns, which is operated only under part 91, and approves it for return to service. What must the record entry include besides the description and date?
- No entry, because preventive maintenance by an owner is not recorded
- The pilot's signature, pilot certificate number, and kind of certificate
- An A&P mechanic's countersignature with the mechanic's certificate number
Show answer
Answer: B. Owner-pilots may do preventive maintenance under 14 CFR 43.3(g), and 43.9 applies to preventive maintenance just as to other maintenance. The person approving signs with their certificate number and kind of certificate, here the pilot certificate; no mechanic countersignature is needed.
Source: 14 CFR 43.9; 14 CFR 43.3
AM.I.I.K3 g4-010
A mechanic completes a minor repair to a wingtip fairing. What record does the regulation require?
- A FAA Form 337, because every repair must be reported to the FAA
- A FAA Form 337, because AC 43.13-1B methods were used
- A maintenance record entry under 14 CFR 43.9, with no FAA Form 337
Show answer
Answer: C. Form 337 is required only for major repairs and major alterations (14 CFR 43.9(d) and Part 43 Appendix B). A minor repair is recorded with the normal 43.9 entry. Using AC 43.13-1B data does not make a repair major or trigger a 337.
Source: 14 CFR 43.9; 14 CFR Part 43 Appendix B
AM.I.I.K5 g4-013
A mechanic keeps finding the same crack in one type of engine mount fitting on several airplanes and wants the FAA to know about this service difficulty. Which form is meant for that report?
- FAA Form 8010-4, Malfunction or Defect Report
- FAA Form 337, Major Repair and Alteration
- FAA Form 8130-3, Authorized Release Certificate
Show answer
Answer: A. FAA Form 8010-4 reports malfunctions and defects to the FAA's service difficulty reporting system, where trends can lead to corrective action such as ADs. Form 337 records major repairs and alterations, and Form 8130-3 releases a part as airworthy; neither is a defect report.
Source: FAA-H-8083-30B, Regulations, Maintenance Forms, Records, and Publications
AM.I.I.K5 g4-014
An overhauled fuel pump arrives from a certificated repair station with an FAA Form 8130-3. What does this form provide?
- FAA approval to install the pump on any aircraft model
- An airworthiness release identifying the part and the work done to it
- Proof that every AD on the receiving airplane has been complied with
Show answer
Answer: B. FAA Form 8130-3, Authorized Release Certificate (Airworthiness Approval Tag), identifies the part and its status after manufacture or maintenance and releases it as airworthy. It does not establish eligibility for a given aircraft; the installer must still confirm eligibility and AD status from the aircraft's data.
Source: FAA-H-8083-30B, Regulations, Maintenance Forms, Records, and Publications
AM.II.D.K2 a2-040
Which item is required in a maintenance record entry made under 14 CFR 43.9 for a repair?
- The aircraft total time in service
- The labor hours spent on the job
- The date the work was completed
Show answer
Answer: C. 14 CFR 43.9(a) requires a description of the work, the date of completion, the name of the person who did the work if different from the signer, and the approver's signature, certificate number and kind of certificate. Total time in service is required in an inspection entry under 43.11, not a 43.9 maintenance entry. Labor hours are not required.
Source: 14 CFR 43.9(a)
AM.II.D.K2 a2-041
A mechanic finishes an annual inspection and finds a cracked exhaust stack that the owner does not want repaired at this shop. What must the mechanic do?
- Leave the inspection entry unsigned until the owner has the crack repaired elsewhere
- Enter it as not airworthy and give the owner a signed, dated discrepancy list
- Sign the aircraft off as airworthy and record the crack as a recommended repair
Show answer
Answer: B. Under 14 CFR 43.11, the inspector makes an entry stating the aircraft is not approved for return to service and gives the owner a signed and dated list of the discrepancies. The inspection is complete, so leaving the record unsigned is wrong. Approving the airplane with a known airworthiness defect is not allowed.
Source: 14 CFR 43.11(a)(5), (b)
AM.II.D.K2 a2-043
An uncertificated helper replaces a cabin door seal under the direct supervision of a certificated mechanic, who then approves the work. What does the 43.9 entry need besides the description, date, and the mechanic's signature and certificate data?
- The name of the helper who performed the work
- The helper's signature and employee number
- Nothing more, since only the approving mechanic is named
Show answer
Answer: A. 14 CFR 43.9(a)(3) requires the name of the person performing the work when that person is different from the person approving it under 43.9(a)(4). Work done under the direct supervision of a certificated mechanic (14 CFR 43.3(d)) is still performed by the helper, so the helper's name goes in the record. The helper does not approve the work, so no helper signature or employee number is required.
Source: 14 CFR 43.9(a)
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- How long does the O&P take?
- The FAA documents do not set a length; it depends on the ratings tested and how many codes you missed. Ask the DME at the pre-test interview.
- Can I bring my own tools?
- Only at the examiner's discretion. The examiner provides the tools, equipment and references, and nonprogrammable calculators are allowed where appropriate (FAA-G-ACS-1, chapter 6).
- Can I take the O&P before the written tests?
- Only as a Part 147 student whose school shows the FAA you are ready, under 14 CFR 65.80. Otherwise the written tests come first (14 CFR 65.75(b)).
Sources
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-11.
- Airman Testing Community Advisory, October 2026 edition (AMT practical test banks, PSI platform, test assessments). FAA Training and Certification Group. Read 2026-11-11.
- 14 CFR 65.79, skill requirements (oral and practical tests). eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-11.
- 14 CFR 65.80, Part 147 students taking the oral and practical early. eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-11.
- 14 CFR 65.19, retesting after failure. eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-11.
- Become a Mechanic: Frequently Asked Questions. FAA. Read 2026-11-11.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.