Military experience to an A&P certificate
Military aviation maintenance experience can count toward the 18 or 30 months that 14 CFR 65.77 requires, depending on your specialty. You either get a military certificate of eligibility through the Joint Service Aviation Maintenance Technician Certification Council (JSAMTCC), or an FAA inspector at a Flight Standards District Office reviews your records and signs Form 8610-2. Service alone does not authorize you to test, and time spent training for a specialty does not count, only time working in it (FAA experience page).
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What is JSAMTCC?
The Department of Defense set up the JSAMTCC with the FAA. It delivers civil aviation training courses to military personnel through the Community College of the Air Force and evaluates aviation specialties for all US branches of service. The FAA lists the specialties it may credit (by MOS, AFSC or NEC) in FAA Order 8900.1, Volume 5, Chapter 5, Section 2, Figure 5-135 (FAA experience page).
What are the two ways in?
| Route | What you do | Your authorization to test |
|---|---|---|
| JSAMTCC | Complete the program for your specialty; your branch documents your training and experience | A military certificate of eligibility for the rating sought |
| FSDO review | Apply at your local Flight Standards District Office with your records; an aviation safety inspector interviews you | FAA Form 8610-2 signed in Block V by the inspector |
Both are accepted at the oral and practical (FAA-G-ACS-1, chapter 6).
What do I bring to the FSDO?
- All documentation of your training and qualifications. Examples the FAA gives: aviation course completion certificates, training records, DD Form 214, and evidence of extra qualifications such as Collateral Duty Inspector, Quality Assurance Representative or an engine turn qualification.
- A letter from your Executive Officer, Maintenance Officer or Classification Officer certifying your length of service, the time you worked in each MOS, NEC or AFSC, the make and model of aircraft or engines you worked on, and where you got the experience.
Source: FAA, Experience Requirements to Become an Aircraft Mechanic.
How much time do I need?
The same as anyone on the experience route: 18 months of practical experience for one rating, or 30 months working on both airframes and powerplants at the same time (14 CFR 65.77). Long hours do not shorten it; the FAA FAQ gives the example of 3,120 hours worked in one year, which still does not equal 18 months (FAA mechanic FAQ).
Do military members pay for the knowledge tests?
Under the agreement between the FAA and the JSAMTCC, these groups can take the AMT knowledge tests at no cost: active-duty, guard and reserve members of all US branches; their dependents; military retirees; DoD civilians; and DHS civilians (FAA mechanic FAQ). The oral and practical has its own fee, set by the examiner.
Can I test while stationed overseas?
Some overseas bases can give FAA knowledge tests, but the FAA says there are no Designated Mechanic Examiners outside the US for the oral and practical (FAA mechanic FAQ). If a test report expires while you serve outside the US, 14 CFR 61.40, applied to mechanics by 65.75(d), gives relief if you finish the practical within 6 calendar months after returning.
What are the steps after eligibility?
- Get an FAA Tracking Number in IACRA and book the written tests with PSI (Scheduling, cost and retakes for the written tests).
- Pass the General test plus Airframe and/or Powerplant.
- Book the oral and practical with a DME (The oral and practical (O&P) test).
Many military mechanics know their own aircraft well and have gaps elsewhere: wood and fabric, reciprocating engines and carburetors, or light aircraft paperwork. A baseline set in each test shows where yours are.
Free mini quiz: 3 practice questions
Three questions from areas military mechanics often meet less: non-metallic structures, piston engine fuel metering, and civil regulations. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.II.B.K5 a1-057
A spruce board for a spar repair has grain that runs off 1 inch in every 12 inches of length. Is it acceptable?
- Yes, because a 1:12 slope is well within the 1:10 maximum limit
- No, because a 1:12 slope is steeper than the 1:15 limit
- Yes, because grain slope limits apply only to plywood, not to solid spars
Show answer
Answer: B. Maximum grain slope is 1 in 15. A 1:12 slope (0.083) is steeper than 1:15 (0.067), so the board is rejected. Cross grain much steeper than the limit sharply reduces strength in solid spar stock. A 1:10 figure is a scarf joint slope, not a grain limit.
Source: AC 43.13-1B, Chapter 1 Wood Structure
AM.III.I.K3 p3-076
In a pressure injection carburetor, what does the automatic mixture control compensate for?
- Changes in air density with altitude and temperature
- Sudden throttle movements during acceleration and deceleration
- Changes in fuel temperature in the carburetor fuel chamber
Show answer
Answer: A. The automatic mixture control uses a sealed bellows that responds to air pressure and temperature, varying the air metering force so fuel flow follows the actual mass of air. Accelerating is handled by a separate accelerating system, and fuel temperature is not what the bellows senses.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Pressure carburetors, automatic mixture control
AM.I.I.K10 g4-024
Under 14 CFR 39.19, who may propose an alternative method of compliance (AMOC) with an AD?
- Only the manufacturer of the affected product, through its service bulletins
- Only a mechanic who holds an inspection authorization, on a Form 337
- Anyone, but it may be used only after the FAA approves it
Show answer
Answer: C. 14 CFR 39.19 says anyone may propose an AMOC or a change in compliance time if it provides an acceptable level of safety. The proposal goes through the principal inspector or to the manager of the office identified in the AD, and it may be used only after that manager approves it.
Source: 14 CFR 39.19
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Does any military aviation job count?
- Only specialties the FAA may credit, and only the time spent working in them. The specialty list is in FAA Order 8900.1, as above.
- Do I still take all the tests?
- Yes. Military applicants take the same written, oral and practical tests as everyone else.
- Where is the list of creditable specialties?
- In FAA Order 8900.1, Volume 5, Chapter 5, Section 2, Figure 5-135, Military Occupational Specialty Codes, which the FAA experience page points to.
Sources
- Experience Requirements to Become an Aircraft Mechanic. FAA. Read 2026-11-14.
- Become a Mechanic: Frequently Asked Questions. FAA. Read 2026-11-14.
- 14 CFR 65.77, experience requirements. eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-14.
- 14 CFR 65.75, knowledge requirements (written tests, early General test). eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-14.
- 14 CFR 61.40, relief for personnel assigned outside the United States in support of U.S. Armed Forces operations. eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.