A&P aircraft drawings practice questions
Aircraft Drawings is ACS area AM.I.B of the FAA General (AMG) test, 5-10% of its 60 questions, so roughly 3 to 6 questions (FAA-G-ACS-1, chapter 3). The ACS lists 4 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.I.B.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for aircraft drawings?
Aircraft drawings tests whether you can read what a drawing, schematic or chart tells you: lines, symbols and dimensions, which revision applies, and whether a repair or alteration matches the type design. The ACS lists only four knowledge elements here, but each one is broad.
| Code | Knowledge element |
|---|---|
| AM.I.B.K1 | Drawings, blueprints, sketches, charts, graphs, and system schematics, including commonly used lines, symbols, and terminology. |
| AM.I.B.K2 | Repair or alteration of an aircraft system or component(s) using drawings, blueprints, or system schematics to determine whether it conforms to its type design. |
| AM.I.B.K3 | Inspection of an aircraft system or component(s) using drawings, blueprints, or system schematics. |
| AM.I.B.K4 | Terms used in conjunction with aircraft drawings, blueprints, or system schematics. |
Source: FAA-S-ACS-1, area AM.I.B, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 4 risk management and 6 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many aircraft drawings questions will I get?
The FAA gives this area 5-10% of the AMG test. On 60 questions that is about 3 to 6 (our arithmetic on the FAA range). Rivetry has 40 reviewed items tagged AM.I.B, 4 of them free.
How should I study aircraft drawings?
- Learn the line types by sight: visible, hidden, center, phantom, extension, dimension, break and sectioning lines (K1, K4).
- Read the title block and revision block first. The risk elements ask you to confirm that the drawing applies to the aircraft by model and serial number and that you hold the current version (R3, R4).
- Practice tolerances. A dimension of 2.500 ±.005 allows any size from 2.495 to 2.505 (R1).
- Charts and graphs come up on all three tests. Read the axis units and every note under the chart before you interpolate (S6).
Learn it from FAA-H-8083-30B, then test yourself.
What could the practical ask me to do?
These are the 6 skill elements the ACS lists for AM.I.B. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Draw a sketch of a repair or alteration.
- S2 Identify the meaning of lines and symbols used in an aircraft drawing.
- S3 Interpret dimensions used in an aircraft drawing.
- S4 Identify changes on an aircraft drawing.
- S5 Determine material requirements from an aircraft drawing.
- S6 Interpret graphs and charts.
The risk management elements for this area: Interpretation of plus or minus tolerances as depicted on aircraft drawings (R1); Specifications for design of alterations and repairs (R2); Applicability of the drawing or schematic to the particular aircraft by model and serial number (R3); Identification of the current version and applicability of drawing being used (R4).
Free mini quiz: 5 practice questions
5 AM.I.B questions: 4 from the app's free set and 1 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.B.K1 g1-062
An installation drawing shows a flap in its extended position using a thin line of long dashes separated by pairs of short dashes. This type of line is a:
- Cutting plane line
- Phantom line
- Hidden line
Show answer
Answer: B. Phantom lines (long dash, two short dashes) show alternate positions of moving parts or the location of adjacent parts. A cutting plane line is heavy and has arrows showing the viewing direction of a section. Hidden lines are evenly spaced short dashes for edges not visible in the view.
Source: FAA-H-8083-30B, Aircraft Drawings / Lines and their meanings; phantom lines
AM.I.B.K1 g1-063
The arrows at the ends of a cutting plane line on a drawing indicate:
- The direction in which the part should be cut during fabrication
- The direction of the material's grain or rolling
- The direction from which the sectional view is seen
Show answer
Answer: C. A cutting plane line marks where the part is imaginarily cut, and its arrows point in the direction of sight for the resulting section view. It is a drawing convention, not a fabrication instruction. Grain direction, when it matters, is given by a note or symbol, not by a cutting plane line.
Source: FAA-H-8083-30B, Aircraft Drawings / Sectional views; cutting plane lines
AM.I.B.K1 g1-064
In a sectional view, the crosshatched (section-lined) areas show:
- Solid surfaces the cutting plane passes through
- Areas that are to be sealed or painted after assembly
- Areas where damage was found and must be repaired
Show answer
Answer: A. Section lining fills the solid surfaces the imaginary cut passes through, and its pattern can indicate the material. Finish and sealing requirements are given in notes or finish callouts, not by crosshatching. Damage areas are not part of a manufacturing drawing's line conventions.
Source: FAA-H-8083-30B, Aircraft Drawings / Sectional views; section lining
AM.I.B.K1 g1-061
On an aircraft drawing, medium-weight dashed lines represent:
- Edges or surfaces hidden in that view
- The center of a hole, arc or symmetrical part
- Alternate positions of a moving part, such as a lever
Show answer
Answer: A. Hidden lines are medium-weight short dashes showing edges that cannot be seen from the viewing direction. Center lines are thin lines of alternating long and short dashes. Alternate positions are shown with phantom lines, made of long dashes separated by pairs of short dashes.
Source: FAA-H-8083-30B, Aircraft Drawings / Lines and their meanings
AM.I.B.K1 g1-065
On a standard three-view orthographic drawing as used in the United States, where is the top view placed?
- Directly below the front view
- Directly above the front view
- To the right of the front view
Show answer
Answer: B. In the third-angle projection used on US drawings, the top view is aligned above the front view and the right side view is placed to the right of the front view. Placing the top view below the front view is the first-angle convention used in some other countries. The space to the right of the front view holds the right side view.
Source: FAA-H-8083-30B, Aircraft Drawings / Orthographic projection
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What kinds of drawings are on the test?
- The ACS names drawings, blueprints, sketches, charts, graphs and system schematics (K1). Figures for written questions come from the FAA testing supplement or are shown on screen.
- Will I have to draw something at the practical?
- You might. The skill elements include drawing a sketch of a repair or alteration (S1), interpreting dimensions (S3) and working out material requirements from a drawing (S5).
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many aircraft drawings questions does Rivetry have?
- 40 reviewed items, 4 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.