A&P practical test projects by ACS area
The practical part of the A&P oral and practical is a set of hands-on projects drawn from the skill elements (S codes) in the ACS. Across the 40 subject areas the ACS lists 519 skill elements, and you are not told in advance which ones you will get. The examiner provides the tools and references, watches every project, and asks questions on the knowledge and risk elements tied to it (FAA-G-ACS-1, chapter 6; FAA-S-ACS-1).
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
How is a practical project graded?
- Return to service standard. Where it applies, your work must meet an approval for return to service standard. If it cannot (a part is out of limits, for example), you explain why.
- References. You must find and apply the right reference. You may use only references the examiner provides, such as 14 CFR, ADs, ACs and manufacturer manuals, all unmarked.
- Safety. PPE, preparation, handling of tools and parts, and following the manufacturer all count. The guide says any disregard for safety results in a failure.
- Calculators and tools. Nonprogrammable calculators are allowed where appropriate; personal tools only at the examiner's discretion.
Source: FAA-G-ACS-1, chapter 6. The examiner may have you simulate a step that would be unsafe.
What do the project verbs mean?
| Verb | FAA meaning |
|---|---|
| Inspect | Examine, with or without inspection-enhancing tools or equipment |
| Check | Verify proper operation |
| Troubleshoot | Analyze and identify malfunctions |
| Service | Perform functions that assure continued operation |
| Repair | Correct a defective condition, including component replacement and adjustment |
| Overhaul | Disassemble, clean, inspect, repair as necessary and reassemble |
Definitions from FAA-G-ACS-1, chapter 6. Many skill elements also start with "Locate and explain", which means finding the procedure in the reference and walking the examiner through it.
How many skill elements does each area have?
| Code | Area | Skill elements | Example (S1) |
|---|---|---|---|
| AM.I.A | Fundamentals of Electricity and Electronics | 14 | Perform circuit continuity test. |
| AM.I.B | Aircraft Drawings | 6 | Draw a sketch of a repair or alteration. |
| AM.I.C | Weight and Balance | 17 | Research and explain the procedures for weighing an aircraft. |
| AM.I.D | Fluid Lines and Fittings | 8 | Fabricate a rigid line with a flare and a bend. |
| AM.I.E | Aircraft Materials, Hardware, and Processes | 14 | Install safety wire on nuts, bolts, and turnbuckles. |
| AM.I.F | Ground Operations and Servicing | 12 | Perform a foreign object damage control procedure. |
| AM.I.G | Cleaning and Corrosion Control | 14 | Perform a portion of an aircraft corrosion inspection. |
| AM.I.H | Mathematics | 8 | Determine the square root of given numbers. |
| AM.I.I | Regulations, Maintenance Forms, Records, and Publications | 18 | Complete an FAA Form 337 for a major repair or alteration. |
| AM.I.J | Physics for Aviation | 8 | Convert temperature units (e.g., from Celsius to Fahrenheit). |
| AM.I.K | Inspection Concepts and Techniques | 8 | Use Vernier calipers. |
| AM.I.L | Human Factors | 3 | File a Malfunction or Defect Report. |
| AM.II.A | Metallic Structures | 14 | Install and remove solid rivets. |
| AM.II.B | Non-Metallic Structures | 12 | Identify appropriate fasteners on composite structures. |
| AM.II.C | Flight Controls | 13 | Identify fixed-wing aircraft rigging adjustment locations. |
| AM.II.D | Airframe Inspection | 7 | Perform an airframe inspection, including a records check. |
| AM.II.E | Landing Gear Systems | 29 | Inspect and service landing gear. |
| AM.II.F | Hydraulic and Pneumatic Systems | 16 | Identify different types of hydraulic fluids. |
| AM.II.G | Environmental Systems | 15 | Inspect an oxygen system. |
| AM.II.H | Aircraft Instrument Systems | 14 | Perform a static system leak test. |
| AM.II.I | Communications, Light Signals, and Runway Lighting Systems | 13 | Make a list of required placards for communication and navigation avionic equipment. |
| AM.II.J | Aircraft Fuel Systems | 18 | Inspect, check, troubleshoot, or repair a fuel system. |
| AM.II.K | Aircraft Electrical Systems | 20 | Inspect aircraft wiring to verify installation and routing. |
| AM.II.L | Ice and Rain Control Systems | 9 | Inspect and operationally check pitot-static anti-ice system. |
| AM.II.M | Airframe Fire Protection Systems | 12 | Troubleshoot an aircraft fire detection or extinguishing system. |
| AM.II.N | Rotorcraft Fundamentals | 4 | Locate components of a helicopter rotor system. |
| AM.II.O | Water and Waste Systems | 2 | Locate and explain the procedures for servicing a lavatory waste system. |
| AM.III.A | Reciprocating Engines | 9 | Perform a cylinder assembly inspection. |
| AM.III.B | Turbine Engines | 13 | Identify different turbine compressors. |
| AM.III.C | Engine Inspection | 14 | Perform a compression check on a cylinder. |
| AM.III.D | Engine Instrument Systems | 19 | Troubleshoot an engine oil temperature/pressure instrument system. |
| AM.III.E | Engine Fire Protection Systems | 14 | Troubleshoot and repair an engine fire detection system. |
| AM.III.F | Engine Electrical Systems | 15 | Inspect engine electrical wiring, switches, and protective devices. |
| AM.III.G | Engine Lubrication Systems | 14 | Inspect an oil cooler or oil lines. |
| AM.III.H | Ignition and Starting Systems | 17 | Set magneto internal timing. |
| AM.III.I | Engine Fuel and Fuel Metering Systems | 30 | Inspect, troubleshoot, and repair a continuous-flow fuel injection system. |
| AM.III.J | Reciprocating Engine Induction and Cooling Systems | 19 | Inspect a carburetor heat system. |
| AM.III.K | Turbine Engine Air Systems | 8 | Perform an induction and cooling system inspection. |
| AM.III.L | Engine Exhaust and Reverser Systems | 7 | Identify the type of exhaust system on a particular aircraft. |
| AM.III.M | Propellers | 12 | Remove and install a propeller. |
Counts and wording from FAA-S-ACS-1; each linked area page lists all of its skill elements.
What changed in the practical test banks in 2026?
The FAA rewrote the practical test banks so practical questions match the assigned project, the aircraft maintenance manual and advisory circulars. The General bank changed on April 20, 2026 and the Airframe bank on July 20, 2026; Powerplant is planned for 2027. Examiners were told to add a liquid penetrant kit for project AM.I.K.S5 by December 2026, and project AM.I.L.S1 has you fill in FAA Form 8010-4 (ATCA, October 2026).
How do I prepare for the projects?
- Read every S element for your ratings; you will not know which you get.
- For each one, find where the procedure lives: the handbook, AC 43.13-1B or a manufacturer manual. "Locate" projects test this directly.
- Practice the measuring and fabrication tasks with real tools if you can: micrometer, vernier caliper, safety wire, flares, rivets, a dye penetrant check.
- Write a sample maintenance record entry for jobs that end in a return to service.
- Say the safety steps out loud before you start, as you would at the test.
Free mini quiz: 4 practice questions
Four questions from areas with many hands-on projects: inspection, hardware, flight controls and ignition. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.K.K2 g4-072
Precision measuring tools in a certificated repair station must be calibrated to what kind of standard?
- Only the tool manufacturer's original factory setting when new
- A standard acceptable to the FAA, typically traceable to NIST
- Another tool of the same type and make kept in the shop toolroom
Show answer
Answer: B. 14 CFR 145.109 requires test and inspection equipment used for airworthiness determinations to be calibrated to a standard acceptable to the FAA, normally traceable to the National Institute of Standards and Technology. Comparing to another shop tool proves nothing if that tool is also off.
Source: 14 CFR 145.109; FAA-H-8083-30B, Inspection Concepts and Techniques
AM.I.E.K2 g2-061
During solution heat treatment of 2024 aluminum alloy, why must the part be quenched with minimal delay after leaving the furnace?
- A delay lets the part cool unevenly, and uneven cooling is the only cause of warping
- A delay lets precipitates form at grain boundaries, causing intergranular corrosion
- A delay lets the Alclad layer diffuse completely into the core alloy and lose protection
Show answer
Answer: B. Solution heat treating dissolves the alloying elements. A prompt quench traps them in solution. If quenching is delayed, they begin to precipitate along the grain boundaries, lowering strength and making the part susceptible to intergranular corrosion. Warping can occur, but it is not the main reason for a fast quench.
Source: FAA-H-8083-30B, Aircraft Materials, Processes, and Hardware / Heat treatment of aluminum alloys
AM.II.C.K3 a2-008
How can a mechanic identify the left-hand threaded end of a turnbuckle barrel?
- A small inspection hole drilled through that end
- A red paint band applied around that end of the barrel
- A groove or knurl around that end of the barrel
Show answer
Answer: C. The left-hand end of the barrel is marked with a groove or knurl so it can be told apart without trying the threads. Small check holes are found on push-pull rod ends to verify thread engagement, not thread direction. Paint bands are not the standard identification.
Source: FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Turnbuckles
AM.III.H.K2 p3-037
A long-reach spark plug is installed in a cylinder that calls for a short-reach plug. What is the likely result?
- The electrodes sit recessed in the bushing and fire poorly, causing hard starting
- Only the installation torque value changes, so the plug works normally once torqued
- Its exposed threads collect carbon, overheat and may cause preignition
Show answer
Answer: C. A plug that is too long projects its threads into the chamber, where they carbon up, can run hot enough to cause preignition, and make removal difficult. A recessed plug that fires in a pocket is the problem when a short-reach plug is put in a long-reach hole.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Spark plug reach
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- How many projects will I do?
- The FAA documents do not give a fixed number. The test is generated per applicant by the Mechanic Test Generator; ask the examiner at the pre-test interview.
- Can I bring my own reference books?
- No. Only references the examiner provides may be used (FAA-G-ACS-1, chapter 6).
- If I fail one project, do I redo everything?
- No. The retest covers the failed projects and any subject areas not tested (FAA-G-ACS-1, chapter 7).
Sources
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- Airman Testing Community Advisory, October 2026 edition (AMT practical test banks, PSI platform, test assessments). FAA Training and Certification Group. Read 2026-11-14.
- 14 CFR 65.79, skill requirements (oral and practical tests). eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.