A&P non-metallic structures practice questions
Non-Metallic Structures is ACS area AM.II.B of the FAA Airframe (AMA) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 29 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.II.B.K1. Below are 6 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for non-metallic structures?
Non-metallic structures is the Airframe area with the most knowledge elements (29): wood structures, fabric covering, composites, thermoplastics and windows, plus seats, restraints and upholstery.
| Code | Knowledge element |
|---|---|
| AM.II.B.K1 | Wood structures, including inspection techniques, tools, and practices for wood structures. |
| AM.II.B.K2 | Effects of moisture/humidity on wood and fabric coverings. |
| AM.II.B.K3 | Types and general characteristics of wood used in aircraft structures. |
| AM.II.B.K4 | Permissible substitutes and other materials used in the construction and repair of wood structures. |
| AM.II.B.K5 | Acceptable and unacceptable wood defects. |
| AM.II.B.K6 | Wood repair techniques and practices. |
| AM.II.B.K7 | Factors used in determining the proper type covering material. |
| AM.II.B.K8 | Types of approved aircraft covering material. |
| AM.II.B.K9 | Seams commonly used with aircraft covering. |
| AM.II.B.K10 | Covering textile terms. |
| AM.II.B.K11 | Structure surface preparation. |
| AM.II.B.K12 | Covering methods commonly used. |
| AM.II.B.K13 | Covering means of attachment. |
| AM.II.B.K14 | Areas on aircraft covering most susceptible to deterioration. |
| AM.II.B.K15 | Aircraft covering preservation/restoration. |
| AM.II.B.K16 | Inspection of aircraft covering. |
| AM.II.B.K17 | Covering repair techniques and practices. |
| AM.II.B.K18 | Inspection/testing of composite structures. |
| AM.II.B.K19 | Types of composite structure defects. |
| AM.II.B.K20 | Composite structure fiber, core, and matrix materials. |
| AM.II.B.K21 | Composite materials storage practices and shelf life. |
| AM.II.B.K22 | Composite repair methods, techniques, fasteners, and practices. |
| AM.II.B.K23 | Thermoplastic material inspection/types of defects. |
| AM.II.B.K24 | Thermoplastic material storage and handling. |
| AM.II.B.K25 | Thermoplastic material installation procedures. |
| AM.II.B.K26 | Care and maintenance of windows. |
| AM.II.B.K27 | Window temporary and permanent repairs. |
| AM.II.B.K28 | Maintenance safety practices/precautions for composite materials/structures, and windows. |
| AM.II.B.K29 | Inspecting restraints and upholstery. |
Source: FAA-S-ACS-1, area AM.II.B, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 7 risk management and 12 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many non-metallic structures questions will I get?
The FAA gives this area 5-10% of the AMA test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 58 reviewed items tagged AM.II.B, 6 of them free.
How should I study non-metallic structures?
- Wood: know the species used in aircraft, with Sitka spruce as the reference, and the acceptable and unacceptable defects (K3 to K5).
- Fabric: learn the covering terms (warp, fill, bias, selvage edge), the seams and the attachment methods such as rib stitching (K9, K10, K13).
- Composites: know fiber, core and matrix materials, storage and shelf life (prepreg is kept frozen), and the tap test for delamination (K18 to K21).
- Windows: clean acrylic with mild soap and plenty of water. Many solvents craze it (K26).
Learn it from FAA-H-8083-31B, then test yourself.
What could the practical ask me to do?
These are the 12 skill elements the ACS lists for AM.II.B. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Identify appropriate fasteners on composite structures.
- S2 Inspect and repair fiberglass.
- S3 Inspect composite, plastic, or glass-laminated structures.
- S4 Clean and inspect acrylic type windshields.
- S5 Locate and explain procedures for a temporary repair to a side window.
- S6 Locate and explain the procedures for tying a modified seine knot.
- S7 Prepare composite surface for painting.
- S8 Perform a tap test on composite material.
- S9 Locate and explain repair standard dimensions.
- S10 Locate and explain repair procedures for elongated bolt holes.
- S11 Determine extent of damage and decide if nonmetallic structure is repairable.
- S12 Perform lay up for a repair to a composite panel, including preparation for vacuum bagging, using a manufacturer’s repair manual.
The risk management elements for this area: Selection of glue (adhesive) or fasteners for aircraft structure (R1); Composite structure repairs (R2); Exposure to materials used in composite repair (R3); Storage of composite materials (R4); Measuring and mixing of materials associated with composite construction (R5); Use of materials that are not part of an approved repair system (R6); Material shelf-life (R7).
Free mini quiz: 6 practice questions
6 AM.II.B questions: 6 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.II.B.K1 a1-052
Inside a wooden wing, a mechanic finds dark water stains around a fitting bolt. What should be done next?
- Refinish the stained area with varnish to seal out further moisture
- Probe the area with a sharp tool to check for softness or decay
- Tighten the fitting bolt to stop further water from entering
Show answer
Answer: B. Water stains show that moisture has been getting in, and moisture causes decay. A sharp probe shows whether the wood is soft or rotted under the stain. Varnishing over it can hide decay, and tightening the bolt can crush the wood without telling you anything about its condition.
Source: FAA-H-8083-31B, Aircraft Wood and Structural Repair / Inspection of wood structures
AM.II.B.K2 a1-053
After a wooden-wing airplane spends a long, hot, dry summer in a hangar, several wing fitting bolts are found loose. The most likely reason is:
- The bolts stretched from repeated flight loads
- Thermal expansion of the steel bolts
- The wood shrank as its moisture content fell
Show answer
Answer: C. Wood shrinks across the grain as it dries and swells as it absorbs moisture. Dry conditions let the fittings loosen, which is why bolt tightness in wood structures is checked periodically. Steel expansion from summer temperatures is far too small to explain loose fittings.
Source: FAA-H-8083-31B, Aircraft Wood and Structural Repair / Effects of moisture on wood
AM.II.B.K3 a1-054
Which wood species is the reference standard against which other aircraft woods are compared?
- Douglas fir
- Sitka spruce
- Mahogany
Show answer
Answer: B. Sitka spruce is the reference wood for aircraft structures because of its high strength for its weight and uniform grain. Other species such as Douglas fir are judged as substitutes by comparing them with spruce. Mahogany is used mainly as plywood faces.
Source: AC 43.13-1B, Chapter 1 Wood Structure; FAA-H-8083-31B, Aircraft Wood and Structural Repair / Wood species
AM.II.B.K4 a1-055
A mechanic considers substituting Douglas fir for spruce in a spar repair. What is the main drawback of this substitution?
- Douglas fir is much weaker in bending
- Douglas fir cannot be glued with aircraft adhesives
- Douglas fir is considerably heavier
Show answer
Answer: C. Douglas fir equals or exceeds spruce in most strength properties, so it is an accepted substitute, but it is considerably heavier. Weight is the penalty. It is not weaker in bending, and it can be glued satisfactorily.
Source: AC 43.13-1B, Chapter 1 Wood Structure (Table 1-1)
AM.II.B.K5 a1-056
Which defect makes aircraft spruce unacceptable for structural use regardless of size?
- Compression wood
- Mineral streaks with no decay present
- A small, sound pin knot
Show answer
Answer: A. Compression wood is abnormally dense, brittle wood that is weak in tension and shrinks unevenly, and it is not acceptable in aircraft structure. Mineral streaks are acceptable if careful inspection finds no decay, and small sound pin knots are allowed within limits.
Source: AC 43.13-1B, Chapter 1 Wood Structure
AM.II.B.K1 a1-051
While inspecting a wooden wing spar, a mechanic taps along a glued joint with a light plastic hammer and hears a dull, dead sound in one area. This most likely indicates:
- A separated glue joint or decay
- Normal variation in the wood grain
- Excess glue squeezed out of the joint
Show answer
Answer: A. A sound joint gives a clear, sharp note when tapped. A dull or dead sound points to a separated joint or decay, which is then probed and examined further. Normal grain variation and glue squeeze-out do not change the sound that much.
Source: FAA-H-8083-31B, Aircraft Wood and Structural Repair / Inspection of wood structures
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Is the seine knot really tested?
- Locating and explaining the procedure for tying a modified seine knot is a skill element (S6). It is used in rib lacing on fabric-covered aircraft.
- Can I swap in a different resin?
- No. Using materials that are not part of the approved repair system is a named risk element (R6).
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many non-metallic structures questions does Rivetry have?
- 58 reviewed items, 6 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.