A&P Airframe (AMA) practice test
The FAA Airframe test (AMA) has 100 multiple-choice questions, a 2-hour limit and a 70% passing score, drawn from 15 subject areas of the Airman Certification Standards, from metallic structures to water and waste systems (FAA-G-ACS-1). Below are 15 free practice questions, one from each area, with the answer and explanation behind each one.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-11); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What is on the AMA test?
The companion guide gives a range for each area's share of the questions. Rivetry's own item count per area is in the last column.
| ACS area | Subject | FAA share of test | Rivetry items |
|---|---|---|---|
| AM.II.A | Metallic Structures | 5-15% | 63 |
| AM.II.B | Non-Metallic Structures | 5-10% | 58 |
| AM.II.C | Flight Controls | 5-10% | 51 |
| AM.II.D | Airframe Inspection | 5-15% | 45 |
| AM.II.E | Landing Gear Systems | 5-10% | 50 |
| AM.II.F | Hydraulic and Pneumatic Systems | 5-10% | 51 |
| AM.II.G | Environmental Systems | 5-10% | 46 |
| AM.II.H | Aircraft Instrument Systems | 5-10% | 49 |
| AM.II.I | Communications, Light Signals, and Runway Lighting Systems | 5-10% | 31 |
| AM.II.J | Aircraft Fuel Systems | 5-10% | 44 |
| AM.II.K | Aircraft Electrical Systems | 5-10% | 55 |
| AM.II.L | Ice and Rain Control Systems | 5-10% | 33 |
| AM.II.M | Airframe Fire Protection Systems | 5-10% | 33 |
| AM.II.N | Rotorcraft Fundamentals | 5-10% | 38 |
| AM.II.O | Water and Waste Systems | 5-10% | 20 |
Sources: FAA-G-ACS-1, chapter 3 (test blueprint); FAA-S-ACS-1 (area codes). Rivetry has 667 Airframe items in total.
You take the Airframe test for the airframe rating, together with the General test if this is your first certificate (testing matrix).
How should I study for the AMA?
- Study by ACS code. Your test report lists the codes you missed, such as AM.II.A.K1, and the examiner retests those codes during the oral. Track your weak areas by the same codes.
- Use the FAA handbook. The FAA says many AMT test questions are based on its AMT handbooks (FAA); for this test start with FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe.
- Practice the calculations. The FAA test tips say to read every note on a calculation question and that you may ask for a printed copy of a graph to mark up (FAA-G-ACS-1, chapter 4).
- Time yourself. 100 questions in 120 minutes is 1.2 minutes per question. Mark hard questions for review and come back to them.
Worked calculations for this test
- Bus load and Watt's law AM.II.K.K1
- Bend allowance and flat length AM.II.A.K4
- Rivet selection and layout AM.II.A.K7
- Accumulator precharge and temperature AM.II.F.K7
- Actuator force AM.II.F.K2
Practice by ACS area
Every AMA area has its own page with the FAA knowledge and skill elements and free questions.
- AMA metallic structures practice questions
- AMA aircraft electrical systems practice questions
- AMA composite, wood and fabric practice questions
- AMA flight controls and rigging practice questions
- AMA airframe inspection practice questions
- AMA landing gear practice questions
- AMA hydraulic and pneumatic practice questions
- AMA environmental and oxygen practice questions
- AMA aircraft instruments practice questions
- AMA avionics practice questions
- AMA aircraft fuel systems practice questions
- AMA ice and rain control practice questions
- AMA airframe fire protection practice questions
- AMA rotorcraft practice questions
- AMA water and waste systems practice questions
- Planning your preparation: A&P written test study plan and A&P test prep options compared
Free mini quiz: 15 practice questions
One question from each of the 15 AMA areas, in ACS order. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.II.A.K2 a1-006
A sheet metal part has a small notch on its edge where metal was pushed aside, with little or no metal removed. This defect is a:
- Nick
- Gouge
- Score
Show answer
Answer: A. A nick is a local notch or break on an edge, usually from metal being displaced rather than removed. A gouge is a groove in the surface from contact with a foreign object under heavy pressure, and a score is a deep scratch on a surface, not a notch on an edge.
Source: FAA-H-8083-31B, Aircraft Metal Structural Repair / Types of damage and defects
AM.II.B.K1 a1-051
While inspecting a wooden wing spar, a mechanic taps along a glued joint with a light plastic hammer and hears a dull, dead sound in one area. This most likely indicates:
- A separated glue joint or decay
- Normal variation in the wood grain
- Excess glue squeezed out of the joint
Show answer
Answer: A. A sound joint gives a clear, sharp note when tapped. A dull or dead sound points to a separated joint or decay, which is then probed and examined further. Normal grain variation and glue squeeze-out do not change the sound that much.
Source: FAA-H-8083-31B, Aircraft Wood and Structural Repair / Inspection of wood structures
AM.II.C.K1 a2-002
What is the smallest diameter of steel cable that should be used in a primary flight control system?
- 1/16 inch
- 3/32 inch
- 1/8 inch
Show answer
Answer: C. Primary control cables should be no smaller than 1/8 inch in diameter, which gives the strength and wear margin needed for elevator, aileron and rudder runs. Smaller sizes such as 1/16 or 3/32 inch appear in trim tab, light secondary, or nonflight control runs but are below the primary-control minimum.
Source: AC 43.13-1B, Chapter 7, Aircraft Hardware, Control Cables, and Turnbuckles; FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Cable types
AM.II.D.K1 a2-038
A private owner pays a freelance flight instructor to give the owner instruction in the owner's own airplane. Under 14 CFR 91.409, does this use require 100-hour inspections?
- No, because the airplane is not provided by the person giving the instruction
- Yes, because the flight instruction is being given for hire
- Yes, because any airplane used for instruction needs 100-hour inspections
Show answer
Answer: A. The 100-hour requirement applies to an aircraft that carries a person for hire or that is provided by the person giving flight instruction for hire. Here the owner provides the airplane, so annual inspections are enough. The fact that the instructor is paid does not trigger the rule on its own.
Source: 14 CFR 91.409(b)
AM.II.E.K1 a2-063
On a hydraulically retracted landing gear with a free-fall emergency extension system, what lowers the gear when the pilot pulls the emergency handle?
- The handle opens an accumulator that drives the actuators to the down position
- The handle starts a backup electric pump that powers the gear down
- The handle releases the uplocks, and gravity and air loads swing the gear down
Show answer
Answer: C. A free-fall system mechanically releases the uplocks (and often the door locks) so the gear drops by its own weight, helped by airflow and sometimes springs, until the downlocks engage. Accumulator or compressed-gas blowdown and auxiliary pumps are different emergency methods used on other designs.
Source: FAA-H-8083-31B, Aircraft Landing Gear Systems / Emergency extension systems
AM.II.F.K1 a3-001
While inspecting a transport-category airplane's wheel well, a mechanic finds light purple fluid seeping from a brake line fitting. Which type of hydraulic fluid is this most likely to be?
- A phosphate ester-based, fire-resistant fluid
- A mineral-based fluid dyed red for identification
- A vegetable-based fluid dyed blue for identification
Show answer
Answer: A. Phosphate ester fluids such as Skydrol are dyed light purple and are used in most transport-category hydraulic systems. Mineral-based MIL-H-5606 is red, and the obsolete vegetable-based fluid was blue. Color is a clue only; confirm the fluid on the servicing placard before adding any.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / hydraulic fluids
AM.II.G.K1 a3-039
A pressurized airplane cruises at 35,000 feet with an 8,000-foot cabin altitude. Using 3.5 psi for outside pressure and 10.9 psi for the pressure at 8,000 feet, what is the cabin pressure differential?
- 11.2 psi
- 14.4 psi
- 7.4 psi
Show answer
Answer: C. Differential = cabin pressure - outside pressure = 10.9 - 3.5 = 7.4 psi. 11.2 psi comes from subtracting outside pressure from sea-level pressure (14.7 - 3.5), and 14.4 psi from adding the two pressures instead of subtracting.
Source: FAA-H-8083-31B, Cabin Environmental Control Systems / pressurization terms
AM.II.H.K1 a3-067
During a ground check, a hydraulic pump LOW PRESSURE annunciator illuminates amber. Under the standard annunciator color convention, how should the amber indication be interpreted?
- A warning: a hazard that requires immediate corrective action
- An advisory: information that a normal system is operating or selected
- A caution: an abnormal condition that needs attention, not immediate action
Show answer
Answer: C. Under the alerting color convention in FAA-H-8083-31B and 14 CFR 25.1322, red marks a warning that needs immediate awareness and immediate response, amber or yellow marks a caution that needs immediate awareness and a subsequent response, and green shows safe operation; advisory and status lights use other colors such as white or blue. Some aircraft show certain low-pressure conditions in red, so always check the aircraft's own annunciator legend. This light is amber, so it is a caution.
Source: FAA-H-8083-31B, Aircraft Instrument Systems / annunciator systems; 14 CFR 25.1322
AM.II.I.K1 a4-001
How does the ideal physical length of a simple antenna relate to the frequency it is designed to transmit or receive?
- It becomes longer as frequency rises, because higher frequencies need more metal to radiate
- It becomes shorter as frequency rises, because the wavelength gets shorter
- It stays the same at any frequency and depends only on transmitter power
Show answer
Answer: B. Wavelength equals the speed of light divided by frequency, so a higher frequency means a shorter wave, and resonant antennas are cut to a fraction of it (often a quarter wave). At 121.5 MHz a quarter wave is about 62 cm. Transmitter power affects range, not the resonant length.
Source: FAA-H-8083-31B, Communication and Navigation / radio waves and antennas
AM.II.J.K1 a4-023
Why does a typical carbureted high-wing light airplane often have no fuel pump in its fuel system?
- The carburetor float chamber produces enough suction to draw fuel from the tanks
- Fuel pumps are not permitted in systems that feed from wing tanks
- The tanks sit above the carburetor, so gravity alone supplies enough fuel pressure
Show answer
Answer: C. In a gravity-feed system the wing tanks are well above the carburetor, and the head of fuel provides the pressure needed to keep the float chamber full. A carburetor does not pull fuel from the tanks by suction, and low-wing airplanes with wing tanks routinely use pumps.
Source: FAA-H-8083-31B, Aircraft Fuel System / gravity-feed systems
AM.II.K.K1 a4-053
What is the function of the reverse-current cutout relay in a DC generator system?
- It reverses the generator field polarity whenever residual magnetism is lost
- It opens the generator circuit if generator voltage drops below battery voltage
- It limits generator output current to the maximum on the generator's data plate
Show answer
Answer: B. When generator voltage drops below battery voltage, as at low rpm or shutdown, current would flow back from the battery and motor the generator. The reverse-current relay opens to prevent this. Limiting output current is the job of the current limiter.
Source: FAA-H-8083-31B, Aircraft Electrical System / DC generator control
AM.II.L.K1 a5-001
Supercooled water drops that are relatively large strike a wing leading edge, spread out, and freeze slowly as they flow aft. What type of ice does this form?
- Rime ice, which is rough, milky, and brittle
- Frost, which forms as a thin, feathery crystalline deposit on the skin
- Clear (glaze) ice, which is hard, heavy, and hard to remove
Show answer
Answer: C. Large supercooled drops do not freeze instantly; they flow back before freezing and form clear (glaze) ice that is dense and bonds tightly. Rime ice comes from small drops that freeze on impact, trapping air and giving a rough, milky deposit.
Source: FAA-H-8083-31B, Ice and Rain Protection / Formation and types of ice
AM.II.M.K1 a5-021
Overheat detection is being installed in a main landing gear wheel well, where there is very little airflow. Which fire zone classification describes this area?
- Class A
- Class D
- Class B
Show answer
Answer: B. A Class D zone has very little or no airflow, such as wing compartments and wheel wells. Class A zones have large airflow past regularly arranged obstructions (such as a reciprocating engine's power section), and Class B zones have large airflow past aerodynamically clean obstructions.
Source: FAA-H-8083-31B, Fire Protection Systems / Fire zones
AM.II.N.K1 a5-045
In forward flight the advancing blade has a higher airspeed than the retreating blade. What mainly equalizes lift across the rotor disc?
- The tail rotor adding extra thrust on the retreating side of the disc
- The lead-lag hinge letting the advancing blade swing aft and lose lift
- Blade flapping: the advancing blade rises and loses angle of attack
Show answer
Answer: C. Dissymmetry of lift is corrected by flapping. The advancing blade flaps up, which reduces its angle of attack, while the retreating blade flaps down and gains angle of attack, balancing lift. Lead-lag hinges relieve in-plane forces, and the tail rotor counters torque.
Source: FAA-H-8083-21B, Aerodynamics of Flight / Dissymmetry of lift
AM.II.O.K1 a5-071
On a typical transport airplane, how is potable water delivered under pressure to the galley and lavatory faucets?
- Gravity flow from a header tank mounted above the cabin ceiling
- Air pressure on the tank from bleed air or a compressor
- A hydraulic-driven pump installed at each galley and lavatory
Show answer
Answer: B. Most airliners pressurize the potable water tank with air from the pneumatic (bleed) system or from a dedicated air compressor, which pushes water through the distribution lines. Gravity alone cannot reach outlets around the cabin, and hydraulic pumps are not used to move potable water.
Source: FAA-H-8083-31B, Water and Waste Systems / Potable water systems
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Are these the real FAA AMA questions?
- No. The FAA does not publish its live test questions. These are original practice items written from the FAA handbooks and regulations and tagged with the ACS code they practice.
- What score do I need?
- 70 percent on each test (14 CFR 65.17).
- Does a practice score predict my result?
- No. Use practice to find weak ACS areas. Rivetry does not publish pass rates or predictions.
Sources
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-11.
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-11.
- FAA Airman Knowledge Testing Matrix (revised September 25, 2026): AMT and IA pages. FAA. Read 2026-11-11.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-11.
- Become an Aviation Mechanic. FAA. Read 2026-11-11.
- 14 CFR 65.17, tests: general procedure (70 percent minimum passing grade). eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-11.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.