A&P hydraulic and pneumatic systems practice questions
Hydraulic and Pneumatic Systems is ACS area AM.II.F of the FAA Airframe (AMA) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 11 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.II.F.K1. Below are 6 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for hydraulic and pneumatic systems?
Hydraulic and pneumatic systems covers fluids, pumps, valves, accumulators, seals, filters and the pneumatic systems that do similar jobs with air. Fluid and seal compatibility is a favorite theme.
| Code | Knowledge element |
|---|---|
| AM.II.F.K1 | Hydraulic system components and fluids. |
| AM.II.F.K2 | Hydraulic system operation. |
| AM.II.F.K3 | Hydraulic system servicing requirements. |
| AM.II.F.K4 | Hydraulic system inspection, check, servicing, and troubleshooting. |
| AM.II.F.K5 | Pneumatic system types and components. |
| AM.II.F.K6 | Pneumatic system servicing requirements. |
| AM.II.F.K7 | Servicing, function, and operation of accumulators. |
| AM.II.F.K8 | Types of hydraulic/pneumatic seals and fluid/seal compatibility. |
| AM.II.F.K9 | Hoses, lines, and fittings. |
| AM.II.F.K10 | Pressure regulators, restrictors, and valves. |
| AM.II.F.K11 | Filter maintenance procedures. |
Source: FAA-S-ACS-1, area AM.II.F, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 5 risk management and 16 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many hydraulic and pneumatic systems questions will I get?
The FAA gives this area 5-10% of the AMA test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 51 reviewed items tagged AM.II.F, 6 of them free.
How should I study hydraulic and pneumatic systems?
- Match fluids to seals: mineral-based fluid (red) with Buna-N (nitrile) seals, phosphate ester fluid (purple, Skydrol type) with butyl or EPR seals. Never mix fluids (K1, K8, R4).
- Precharge an accumulator with nitrogen or air to the manufacturer's figure with system fluid pressure relieved. The gas law workup shows how precharge changes with temperature (K7, S7).
- Force on a piston = pressure × area. On the rod side, subtract the rod's area first; the actuator force workup does the arithmetic.
- Relieve system pressure before you open any line or component (R1).
Learn it from FAA-H-8083-31B, then test yourself.
What could the practical ask me to do?
These are the 16 skill elements the ACS lists for AM.II.F. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Identify different types of hydraulic fluids.
- S2 Identify different packing seals.
- S3 Install seals and backup rings in a hydraulic component.
- S4 Remove and install a selector valve.
- S5 Check a pressure regulator and adjust as necessary.
- S6 Remove, clean, inspect, and install a hydraulic system filter.
- S7 Service a hydraulic system accumulator.
- S8 Service a hydraulic system reservoir.
- S9 Remove, install, and perform an operational check of a hydraulic pump.
- S10 Locate procedures for checking pneumatic/bleed air overheat warning systems.
- S11 Purge air from a hydraulic system.
- S12 Remove and install a system pressure relief valve.
- S13 Inspect a hydraulic or pneumatic system for leaks.
- S14 Troubleshoot a hydraulic or pneumatic system for leaks.
- S15 Locate and explain hydraulic fluid servicing instructions and identify/select fluid for a given aircraft.
- S16 Locate installation procedures for a seal, backup ring, or gasket.
The risk management elements for this area: Relieving system pressure prior to system servicing or disassembly (R1); High pressure gases and fluids (R2); Storage and handling of hydraulic fluids (R3); Cross-contamination of hydraulic fluids (R4); Compatibility between hydraulic seals and hydraulic fluids (R5).
Worked calculations for this area
- Accumulator precharge and temperature AM.II.F.K7
- Actuator force AM.II.F.K2
Free mini quiz: 6 practice questions
6 AM.II.F questions: 6 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.II.F.K1 a3-002
What is the purpose of the shear section built into the drive shaft of an engine-driven hydraulic pump?
- It lets the pump slip when cold fluid is too thick to move
- It breaks if the pump seizes, protecting the engine accessory drive
- It breaks if system pressure exceeds the relief valve setting
Show answer
Answer: B. The shear section is a deliberate weak point, so a seized or jammed pump snaps it instead of damaging the engine gearbox. Protecting the system from overpressure is the job of the relief valve, not the pump drive shaft.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / engine-driven pumps
AM.II.F.K1 a3-003
A hydraulic reservoir feeds the engine-driven pump through a standpipe and the emergency hand pump from an outlet at the very bottom. A pressure line ruptures and the engine pump drains the reservoir down to the top of the standpipe. What fluid remains usable?
- None, because both pumps draw from the same level
- Enough for the engine pump once the reservoir is repressurized
- A reserve below the standpipe that only the hand pump can draw
Show answer
Answer: C. The engine-driven pump draws through the standpipe, so a leak it feeds can only drain the reservoir to the top of that pipe. The fluid below it stays available to the emergency hand pump, which draws from the bottom outlet. Repressurizing the reservoir does not lower the standpipe inlet.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / reservoirs
AM.II.F.K1 a3-004
A closed-center hydraulic system uses a constant-displacement gear pump. What keeps the pump from working against full system pressure when no actuator is moving?
- A thermal relief valve that opens whenever the selectors are in neutral
- A compensator that reduces the pump's piston stroke to zero
- A pressure regulator (unloading valve) that routes pump output to return
Show answer
Answer: C. A constant-displacement pump moves a fixed volume per revolution, so a regulator or unloading valve diverts its output to return once kick-out pressure is reached while a check valve holds system pressure. A stroke-reducing compensator exists only in variable-displacement piston pumps, not gear pumps.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / pumps and pressure regulators
AM.II.F.K2 a3-005
An actuator piston has a 2.0-inch diameter. With 3,000 psi applied to the full piston face, about how much force does it produce?
- About 9,400 lb
- About 37,700 lb
- About 6,000 lb
Show answer
Answer: A. Force = pressure x area. Area = pi x (1.0 in)^2 = 3.14 sq in, so 3,000 x 3.14 = about 9,425 lb. Using the 2-inch diameter as the radius gives pi x 4 = 12.57 sq in and a force four times too large, about 37,700 lb.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / Pascal's law and actuating cylinders
AM.II.F.K2 a3-007
In an open-center hydraulic system, how are the selector valves arranged, and where does pump output go when none of them is operated?
- In parallel; the pump holds full pressure against the closed valves
- In series; fluid flows through them back to the reservoir at low pressure
- In series; an unloading valve holds the system at full pressure
Show answer
Answer: B. Open-center selectors are plumbed in series, and with all of them in neutral the pump output circulates freely to the reservoir, so pressure builds only when a selector is moved. Parallel selectors with fluid held at full pressure describe a closed-center system.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / open-center and closed-center systems
AM.II.F.K1 a3-001
While inspecting a transport-category airplane's wheel well, a mechanic finds light purple fluid seeping from a brake line fitting. Which type of hydraulic fluid is this most likely to be?
- A phosphate ester-based, fire-resistant fluid
- A mineral-based fluid dyed red for identification
- A vegetable-based fluid dyed blue for identification
Show answer
Answer: A. Phosphate ester fluids such as Skydrol are dyed light purple and are used in most transport-category hydraulic systems. Mineral-based MIL-H-5606 is red, and the obsolete vegetable-based fluid was blue. Color is a clue only; confirm the fluid on the servicing placard before adding any.
Source: FAA-H-8083-31B, Hydraulic and Pneumatic Power Systems / hydraulic fluids
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What color is MIL-PRF-5606 fluid?
- Red. It is a mineral-based fluid used in many light aircraft and older systems.
- Which side does a backup ring go on?
- The side away from the pressure, so it supports the O-ring. Installing seals and backup rings is skill element S3.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many hydraulic and pneumatic systems questions does Rivetry have?
- 51 reviewed items, 6 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.