A&P fluid lines and fittings practice questions
Fluid Lines and Fittings is ACS area AM.I.D of the FAA General (AMG) test, 5-10% of its 60 questions, so roughly 3 to 6 questions (FAA-G-ACS-1, chapter 3). The ACS lists 6 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.I.D.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for fluid lines and fittings?
Fluid lines and fittings covers rigid tubing and flexible hose from identification to fabrication, installation and inspection, plus the torque and witness-mark practices that keep fittings from working loose.
| Code | Knowledge element |
|---|---|
| AM.I.D.K1 | Tubing and hose materials, applications, sizes, and fittings. |
| AM.I.D.K2 | Rigid line or flexible hose material identification. |
| AM.I.D.K3 | Rigid line fabrication, installation, and inspection techniques/practices. |
| AM.I.D.K4 | Flexible hose fabrication, installation, and inspection techniques/practices. |
| AM.I.D.K5 | Importance of using a torque wrench when securing fluid hose and line fittings. |
| AM.I.D.K6 | Use of torque seal or similar witness techniques after installing critical fluid hose and line fittings. |
Source: FAA-S-ACS-1, area AM.I.D, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 7 risk management and 8 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many fluid lines and fittings questions will I get?
The FAA gives this area 5-10% of the AMG test. On 60 questions that is about 3 to 6 (our arithmetic on the FAA range). Rivetry has 38 reviewed items tagged AM.I.D, 4 of them free.
How should I study fluid lines and fittings?
- Know how rigid tubing is sized: the dash number is the outside diameter in sixteenths of an inch, so a -6 tube is 6/16 (3/8) inch OD (K1, K2).
- Study flared and flareless fittings as fabrication steps: cut, deburr, flare or preset the sleeve, then inspect (K3, S1, S8). The AN flare angle is 37 degrees, and single and double flares are common question material.
- For flexible hose, learn the installation rules: no twist (the lay line shows it), some slack, the minimum bend radius and proper support (K4, R5).
- Torque the fittings. K5 covers why a torque wrench is used on hose and line fittings, and K6 the torque seal or other witness mark on critical fittings.
Learn it from FAA-H-8083-30B, then test yourself.
What could the practical ask me to do?
These are the 8 skill elements the ACS lists for AM.I.D. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Fabricate a rigid line with a flare and a bend.
- S2 Install an aircraft rigid line.
- S3 Install an aircraft flexible hose.
- S4 Perform a rigid line or flexible hose inspection.
- S5 Identify installation and security requirements for rigid lines and flexible hoses.
- S6 Identify fluid lines, pneumatic lines, and fittings.
- S7 Fabricate a flexible hose.
- S8 Fabricate a flareless-fitting-tube connection.
The risk management elements for this area: System configuration prior to and during maintenance (R1); Use of required safety equipment (R2); Hazardous fluids (R3); High-pressure fluid systems (R4); A twisted hose (R5); A loosened fitting or a hose that has moved out of position (R6); Use of tools while applying torque to a fluid line (R7).
Free mini quiz: 5 practice questions
5 AM.I.D questions: 4 from the app's free set and 1 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.D.K1 g2-033
A mechanic is offered a 45-degree automotive flare fitting as a replacement for an AN flared fitting. Why should it be rejected?
- AN fittings seal on tapered pipe threads, so the flare angle does not matter
- 45-degree fittings are approved only for oxygen lines in aircraft
- AN fittings use a 37-degree flare, so a 45-degree cone will not seal
Show answer
Answer: C. AN flared fittings use a 37-degree flare angle. A 45-degree automotive fitting may thread on, but the cones do not match, so the joint can leak or fail under pressure. Flared fittings seal at the flare, not on pipe threads.
Source: FAA-H-8083-30B, Fluid Lines and Fittings / Flared tube fittings
AM.I.D.K1 g2-034
How can an AN flared tube fitting be told apart from the older AC fitting it closely resembles?
- The AN fitting has a 45-degree flare cone instead of the AC fitting's 37-degree cone
- The AN fitting has a shoulder between the end of the threads and the flare cone
- The AN fitting is threaded left-hand so it cannot be mixed up with an AC fitting
Show answer
Answer: B. The AN flared fitting has a short shoulder between the end of its threads and the flare cone; the older AC fitting has no shoulder (and its sleeve is noticeably longer). Both use a 37-degree flare and standard right-hand threads, so neither a 45-degree cone nor left-hand threads identify an AN fitting.
Source: FAA-H-8083-30B, Fluid Lines and Fittings / AN and AC fittings
AM.I.D.K1 g2-031
A rigid tube is called out as a -10 size. What is its outside diameter?
- 5/8 in
- 5/16 in
- 1-1/4 in
Show answer
Answer: A. Rigid tube dash numbers give the outside diameter in sixteenths of an inch, so -10 is 10/16 = 5/8 in. 5/16 in reads the number as thirty-seconds, and 1-1/4 in reads it as eighths. Wall thickness is specified separately, in thousandths of an inch.
Source: FAA-H-8083-30B, Fluid Lines and Fittings / Tube sizes
AM.I.D.K1 g2-032
A 3,000 psi hydraulic pressure line runs through a wheel well where it is exposed to debris. Which tubing material is the normal choice?
- 1100-H14 aluminum alloy tubing
- 5052-O aluminum alloy tubing
- Corrosion-resistant steel tubing
Show answer
Answer: C. Corrosion-resistant steel tubing is used for high-pressure hydraulic lines and where lines are exposed to abrasion or heat, as in wheel wells. 5052-O aluminum is a common general-purpose tubing for fuel, oil and lower-pressure systems. 1100-H14 is suited only to low-pressure lines such as instrument and vent lines.
Source: FAA-H-8083-30B, Fluid Lines and Fittings / Tubing materials
AM.I.D.K1 g2-035
A -6 flexible hose assembly is meant to be used with which rigid tubing?
- -6 tubing, which has a 3/8 in outside diameter
- -6 tubing, which has a 3/16 in outside diameter
- -3 tubing, because hose sizes are double tube sizes
Show answer
Answer: A. Flexible hose sizes use the same dash-number system, in sixteenths of an inch, as the rigid tubing they connect to. A -6 hose therefore pairs with -6 tubing, which is 6/16 = 3/8 in OD. Reading the dash number in thirty-seconds gives the wrong 3/16 in.
Source: FAA-H-8083-30B, Fluid Lines and Fittings / Flexible hose sizes
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- How are fluid lines identified on an aircraft?
- With marking tape or bands that use color, words and symbols to show the fluid and its function. The fluid lines chapter of the FAA General handbook (FAA-H-8083-30B) shows the scheme.
- Is hose fabrication on the practical?
- It can be. The skill elements include fabricating a rigid line with a flare and a bend (S1), fabricating a flexible hose (S7) and making a flareless-fitting tube connection (S8).
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many fluid lines and fittings questions does Rivetry have?
- 38 reviewed items, 4 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.