A&P materials, hardware and processes practice questions

Materials, Hardware and Processes is ACS area AM.I.E of the FAA General (AMG) test, 5-10% of its 60 questions, so roughly 3 to 6 questions (FAA-G-ACS-1, chapter 3). The ACS lists 14 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.I.E.K1. Below are 4 free original questions from Rivetry's reviewed bank, with the explanation for each.

Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-12); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.

What does the ACS list for materials, hardware and processes?

Materials, hardware and processes is where fasteners, torque, safety wire, measuring tools and weld quality come together, and where torque arithmetic and part identification are easy points to lose.

CodeKnowledge element
AM.I.E.K1Materials commonly used in aircraft and their general application.
AM.I.E.K2Heat treatment and metal working processes.
AM.I.E.K3Forces placed on aircraft materials (e.g., tension, compression, torsion, bending, strain, and shear).
AM.I.E.K4Hardware commonly used in aircraft (e.g., bolts, nuts, screws, pins, washers, turnlock fasteners, cables, cable fittings, and rigid line couplings).
AM.I.E.K5Safety wire and safety clip requirements and techniques.
AM.I.E.K6Precision measurement tools, principles, and procedures.
AM.I.E.K7Soldering preparation, types of solder, and flux usage.
AM.I.E.K8Torquing tools, principles, and procedures.
AM.I.E.K9Suitability and compatibility of materials and hardware used for maintenance.
AM.I.E.K10Relationship between torque and fastener preload.
AM.I.E.K11Identification markings on materials and hardware.
AM.I.E.K12Characteristics of acceptable welds.
AM.I.E.K13Characteristics of unacceptable welds.
AM.I.E.K14Procedures for weld repairs.

Source: FAA-S-ACS-1, area AM.I.E, read 2026-11-12. The written test draws on the knowledge elements. The ACS also lists 4 risk management and 14 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).

How many materials, hardware and processes questions will I get?

The FAA gives this area 5-10% of the AMG test. On 60 questions that is about 3 to 6 (our arithmetic on the FAA range). Rivetry has 40 reviewed items tagged AM.I.E, 4 of them free.

How should I study materials, hardware and processes?

Learn it from FAA-H-8083-30B, then test yourself.

Worked calculations for this area

Free mini quiz: 4 practice questions

4 free AM.I.E questions. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.

  1. AM.I.E.K1 g2-059

    A cluster fitting is specified as SAE 4130 steel. What does the designation tell the mechanic?

    1. Nickel-chromium steel containing about 1.30 percent carbon
    2. Plain carbon steel containing about 0.41 percent carbon
    3. Chromium-molybdenum steel containing about 0.30 percent carbon
    Show answer

    Answer: C. In SAE numbers, the first digits give the alloy family (41xx is chromium-molybdenum) and the last two give carbon in hundredths of a percent (30 = 0.30 percent). Chrome-moly 4130 is common for welded tubing and fittings. Plain carbon steels are the 10xx series.

    Source: FAA-H-8083-30B, Aircraft Materials, Processes, and Hardware / SAE steel numbering

  2. AM.I.E.K2 g2-060

    After a 4130 steel fitting is welded, it is heated above its critical temperature and allowed to cool in still air to relieve welding stresses. What is this process called?

    1. Full annealing
    2. Normalizing
    3. Tempering
    Show answer

    Answer: B. Normalizing heats steel above its critical range and cools it in still air, which relieves stresses from welding, forging or machining. Full annealing also heats above critical, but cools very slowly, usually in the furnace, to get maximum softness. Tempering reheats hardened steel below its critical temperature.

    Source: FAA-H-8083-30B, Aircraft Materials, Processes, and Hardware / Heat treatment of ferrous metals

  3. AM.I.E.K1 g2-057

    Which aluminum alloy cannot be strengthened by heat treatment and is hardened only by cold working?

    1. 5052
    2. 2024
    3. 6061
    Show answer

    Answer: A. The 1xxx, 3xxx and 5xxx series are non-heat-treatable; they are strengthened by strain hardening, shown by -H tempers such as 5052-H32. 2024 (copper alloy) and 6061 (magnesium-silicon alloy) are heat-treatable and appear in -T tempers.

    Source: FAA-H-8083-30B, Aircraft Materials, Processes, and Hardware / Aluminum alloys

    Get Rivetry on Google Play

  4. AM.I.E.K1 g2-058

    What is Alclad 2024 aluminum sheet?

    1. 2024 alloy given a chromate conversion coating at the mill
    2. 2024 alloy with a thin layer of pure aluminum bonded to each surface
    3. Pure aluminum sheet with a thin 2024 skin rolled onto each side
    Show answer

    Answer: B. Alclad is a strong heat-treatable core, here 2024, with a thin layer of commercially pure aluminum bonded to both surfaces. The pure aluminum resists corrosion and protects the core. A chromate conversion coating is a separate surface treatment. Alclad's strength comes from the alloy core, not the cladding.

    Source: FAA-H-8083-30B, Aircraft Materials, Processes, and Hardware / Alclad

Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.

Get Rivetry on Google Play

More questions

Where do I find torque values for real work?
In the manufacturer's maintenance data. AC 43.13-1B has standard torque tables for when the manufacturer gives none; on the test, use the numbers in the question.
Does the test cover soldering?
Yes. The ACS lists soldering preparation, types of solder and flux usage (K7).
Are these the real FAA questions?
No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
How many materials, hardware and processes questions does Rivetry have?
40 reviewed items, 4 of them free.

Sources

Related guides

General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.