A&P written test study plan
Study by ACS area, not by chapter: the FAA gives each area a share of the test (5 to 15 percent), so spend time in proportion, read the matching FAA handbook, practice with timed sets of 60 or 100 questions in 2 hours, and then work the ACS codes you miss (FAA-G-ACS-1). The plan below is a suggested order, not an FAA program; stretch it to the hours you have.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-12).
Which areas carry the most weight?
Every area has a range, and the top end is 15 percent for only a few: General, Fundamentals of Electricity and Electronics (AM.I.A, 5-15%); Ground Operations and Servicing (AM.I.F, 5-15%); Airframe, Metallic Structures (AM.II.A, 5-15%); Airframe Inspection (AM.II.D, 5-15%); Powerplant, Reciprocating Engines (AM.III.A, 5-15%); Engine Electrical Systems (AM.III.F, 5-15%). A 5 to 15 percent area is roughly 5 to 15 questions on a 100-question test, and roughly 3 to 9 on the 60-question General test (our arithmetic on the ranges in FAA-G-ACS-1, chapter 3). Every area is tested, so none can be skipped.
| Test | Questions | Minutes per question | Areas |
|---|---|---|---|
| AMG | 60 | 2.0 | 12 |
| AMA | 100 | 1.2 | 15 |
| AMP | 100 | 1.2 | 13 |
What is a sensible order of study?
- Read the ACS area list for your test (). The codes are what your test report will show.
- Take a short baseline set of free questions (A&P General (AMG) practice test, A&P Airframe (AMA) practice test or A&P Powerplant (AMP) practice test) to find where you start. Treat it as a map, not a prediction.
- Study the heavy areas first, then the rest, with the FAA handbook open: FAA-H-8083-30B for General, -31B for Airframe, -32B for Powerplant.
- Practice the arithmetic by hand. The FAA allows an aviation or simple calculator and says to read every note on a calculation question (FAA-G-ACS-1, chapter 4). The figure bench works the common ones step by step.
- Run timed sets at the real length, then review every wrong answer by its ACS code.
- Re-study the codes you missed and repeat. After the real test your report lists missed codes; use the same habit for the oral (The oral and practical (O&P) test).
What does an example schedule look like?
An example for the General test, assuming about 6 to 8 hours a week. It is our suggestion, not FAA guidance; with less time, stretch each block.
| Week | Focus | Practice |
|---|---|---|
| 1 | Baseline set, electricity and electronics (AM.I.A), mathematics (AM.I.H) | Series-parallel and tank volume workups |
| 2 | Weight and balance (AM.I.C), physics (AM.I.J) | Loaded CG and equipment change workups |
| 3 | Materials and hardware (AM.I.E), fluid lines (AM.I.D), drawings (AM.I.B) | Torque extension workup |
| 4 | Ground operations (AM.I.F), cleaning and corrosion (AM.I.G), inspection (AM.I.K) | Area question sets |
| 5 | Regulations and records (AM.I.I), human factors (AM.I.L) | Rules questions in How to get an A&P license |
| 6 | Two timed 60-question sets, review by ACS code | Re-study every missed code |
For Airframe and Powerplant, give the 15-percent areas an extra week and finish with two timed 100-question sets. Book the real test when your review keeps turning up nothing new, not at a score threshold: practice results do not predict the FAA result.
Where do the questions come from?
The FAA says many AMT test questions are based on its AMT handbooks (FAA, Become an Aviation Mechanic). The FAA does not publish the live questions, so any practice bank, including Rivetry's, is original material (see A&P test prep options compared).
More questions
- How many weeks should I study?
- The FAA gives no recommended time. Go by your results: stop when timed sets stop showing new missed ACS codes. The example above is six weeks for General at 6 to 8 hours a week and is our suggestion only.
- Should I take General first?
- Anyone applying for a first certificate takes General plus Airframe and/or Powerplant, and General material (electricity, math, regulations) supports the other two. A Part 147 student may take General early (14 CFR 65.75(c)).
- Do I need to memorize the handbooks?
- No. Learn the concepts and formulas tied to ACS codes; the questions are multiple choice with one correct answer.
Sources
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-12.
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-12.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General. FAA. Used to write the practice items 2026-11-12.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-12.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-12.
- Become an Aviation Mechanic. FAA. Read 2026-11-12.
- 14 CFR 65.75, knowledge requirements (written tests, early General test). eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-12.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.