A&P Powerplant (AMP) practice test
The FAA Powerplant test (AMP) has 100 multiple-choice questions, a 2-hour limit and a 70% passing score, drawn from 13 subject areas of the Airman Certification Standards, from reciprocating engines to propellers (FAA-G-ACS-1). Below are 13 free practice questions, one from each area, with the answer and explanation behind each one.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-11); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What is on the AMP test?
The companion guide gives a range for each area's share of the questions. Rivetry's own item count per area is in the last column.
| ACS area | Subject | FAA share of test | Rivetry items |
|---|---|---|---|
| AM.III.A | Reciprocating Engines | 5-15% | 81 |
| AM.III.B | Turbine Engines | 5-10% | 68 |
| AM.III.C | Engine Inspection | 5-10% | 40 |
| AM.III.D | Engine Instrument Systems | 5-10% | 40 |
| AM.III.E | Engine Fire Protection Systems | 5-10% | 30 |
| AM.III.F | Engine Electrical Systems | 5-15% | 45 |
| AM.III.G | Engine Lubrication Systems | 5-10% | 44 |
| AM.III.H | Ignition and Starting Systems | 5-10% | 50 |
| AM.III.I | Engine Fuel and Fuel Metering Systems | 5-10% | 51 |
| AM.III.J | Reciprocating Engine Induction and Cooling Systems | 5-10% | 40 |
| AM.III.K | Turbine Engine Air Systems | 5-10% | 35 |
| AM.III.L | Engine Exhaust and Reverser Systems | 5-10% | 36 |
| AM.III.M | Propellers | 5-10% | 57 |
Sources: FAA-G-ACS-1, chapter 3 (test blueprint); FAA-S-ACS-1 (area codes). Rivetry has 617 Powerplant items in total.
You take the Powerplant test for the powerplant rating, together with the General test if this is your first certificate (testing matrix).
How should I study for the AMP?
- Study by ACS code. Your test report lists the codes you missed, such as AM.III.A.K1, and the examiner retests those codes during the oral. Track your weak areas by the same codes.
- Use the FAA handbook. The FAA says many AMT test questions are based on its AMT handbooks (FAA); for this test start with FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant.
- Practice the calculations. The FAA test tips say to read every note on a calculation question and that you may ask for a printed copy of a graph to mark up (FAA-G-ACS-1, chapter 4).
- Time yourself. 100 questions in 120 minutes is 1.2 minutes per question. Mark hard questions for review and come back to them.
Worked calculations for this test
- Displacement and compression ratio AM.III.A.K7
- Indicated horsepower (PLANK) AM.III.A.K7
Practice by ACS area
Every AMP area has its own page with the FAA knowledge and skill elements and free questions.
- AMP reciprocating engines practice questions
- AMP turbine engines practice questions
- AMP propellers practice questions
- AMP engine inspection practice questions
- AMP engine instruments practice questions
- AMP engine fire protection practice questions
- AMP engine electrical practice questions
- AMP engine lubrication practice questions
- AMP ignition and starting practice questions
- AMP fuel metering practice questions
- AMP induction and cooling practice questions
- AMP turbine air systems practice questions
- AMP exhaust and reversers practice questions
- Planning your preparation: A&P written test study plan and A&P test prep options compared
Free mini quiz: 13 practice questions
One question from each of the 13 AMP areas, in ACS order. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.A.K2 p1-005
A mechanic reads these valve events from an engine data plate: intake opens 20 degrees before top center, exhaust closes 15 degrees after top center. What is the valve overlap?
- 5 degrees
- 15 degrees
- 35 degrees
Show answer
Answer: C. Overlap is the period both valves are open around top center: 20 degrees before TC plus 15 degrees after TC = 35 degrees. Subtracting the two numbers (20 - 15 = 5) is the common mistake; the angles lie on opposite sides of top center, so they add.
Source: FAA-H-8083-32B, Aircraft Engines / Valve timing and valve overlap
AM.III.B.K1 p1-059
In the Brayton cycle used by gas turbine engines, combustion takes place at approximately constant:
- Volume
- Temperature
- Pressure
Show answer
Answer: C. In a turbine engine the air flows continuously through the combustor, where fuel is burned while the pressure stays nearly constant and the gas expands. Constant-volume combustion is the Otto cycle of a piston engine, where the charge is burned in a closed cylinder.
Source: FAA-H-8083-32B, Aircraft Engines / Turbine engines / Brayton cycle
AM.III.C.K1 p2-001
An airplane that a flight school provides for flight instruction for hire was due for its 100-hour inspection at 1,200.0 hours. It was flown to 1,206.0 hours to reach the shop, where the inspection was completed. Under 14 CFR 91.409, when is the next 100-hour inspection due?
- 1,306.0 hours
- 1,300.0 hours
- 1,310.0 hours
Show answer
Answer: B. The 100-hour limit may be exceeded by up to 10 hours only to reach a place where the inspection can be done, and the excess time counts toward the next interval: 1,200 + 100 = 1,300 hours. Counting from 1,206 to 1,306 wrongly gives credit for the 6 hours flown past the due point.
Source: 14 CFR 91.409(b)
AM.III.D.K1 p2-027
On a fuel-injected engine whose fuel flow indicator actually senses fuel pressure at the flow divider, the gauge shows higher than normal flow at a given power setting. What is the most likely cause?
- A leaking nozzle line downstream of the flow divider
- An air leak in the induction manifold
- One or more partly clogged injector nozzles
Show answer
Answer: C. Because this indicator is a pressure gauge calibrated in fuel flow, a restricted nozzle raises the pressure and the gauge shows more flow even though less fuel reaches that cylinder. A leaking line lowers the pressure and gives a low reading.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Fuel-injection flow indication
AM.III.E.K1 p2-053
A fire in an engine nacelle fed by leaking jet fuel or engine oil is classified as:
- Class A
- Class C
- Class B
Show answer
Answer: C. Class B fires involve flammable liquids such as fuel, oil, hydraulic fluid, and grease. Class A fires involve ordinary combustibles like wood, cloth, and paper; Class C fires involve energized electrical equipment; Class D fires involve flammable metals.
Source: FAA-H-8083-32B, Engine Fire Protection Systems / Classes of fires
AM.III.F.K1 p2-071
In an aircraft DC generator, what part changes the alternating current induced in the armature coils into direct current at the output?
- The commutator
- The slip rings
- The field windings
Show answer
Answer: A. The commutator segments reverse the armature coil connections to the brushes each half turn, so the output stays in one direction. Slip rings carry current to or from a rotor without rectifying it, and the field windings only make the magnetic field.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / DC generators
AM.III.G.K1 p3-001
An engine manufacturer specifies SAE 50 oil. Which commercial aviation grade number is approximately equivalent?
- Grade 65
- Grade 50
- Grade 100
Show answer
Answer: C. Commercial aviation grade numbers run roughly twice the SAE number, so SAE 50 is about grade 100 and SAE 40 is about grade 80. Reading the numbers as equal (grade 50) is the common slip, and grade 65 matches SAE 30, an oil that is too thin for this engine.
Source: FAA-H-8083-32B, Lubrication and Cooling Systems / Aviation oil grades and viscosity
AM.III.H.K1 p3-031
Why do certificated aircraft piston engines normally have two spark plugs in each cylinder?
- Two plugs share the firing voltage, so each plug needs only half as much
- One plug fires on the compression stroke and the other on the exhaust stroke
- Two flame fronts speed combustion, and one system backs up the other
Show answer
Answer: C. Dual ignition gives two flame fronts for quicker, more complete combustion and provides redundancy if one magneto or its leads fail. Both plugs fire near the end of the compression stroke, and each plug still needs the full firing voltage.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Dual ignition
AM.III.I.K1 p3-069
An engine burns 12.5 gallons of avgas per hour (6 pounds per gallon) while consuming 1,000 pounds of air per hour. What is its fuel/air ratio?
- 13.3
- 0.075
- 0.0125
Show answer
Answer: B. Fuel flow is 12.5 gal/hr x 6 lb/gal = 75 lb/hr, and the fuel/air ratio is 75 / 1,000 = 0.075 (about 1:13.3). Using gallons instead of pounds gives 12.5 / 1,000 = 0.0125, and 13.3 is the air/fuel ratio (1,000 / 75), the inverse of what was asked.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Fuel/air mixtures
AM.III.J.K1 p4-001
A normally aspirated carbureted engine idles roughly, but smooths out as rpm is increased. The mechanic finds a cracked induction hose between the intake pipe and one cylinder. Why is the effect worst at idle?
- At idle the leak blows fuel-air mixture out of the pipe, starving that one cylinder of its charge
- Manifold pressure is lowest at idle, so the leak draws in the most unmetered air for the airflow
- At idle the leak raises manifold pressure, which makes that one cylinder run too rich
Show answer
Answer: B. Below the throttle a normally aspirated engine's manifold is below atmospheric pressure, deepest at idle, so outside air is drawn in and leans that cylinder most when total airflow is small. Mixture blowing out of a leak happens only where manifold pressure is above ambient, as on a boosted engine.
Source: FAA-H-8083-32B, Induction and Exhaust Systems / Reciprocating engine induction systems
AM.III.K.K1 p4-027
Of the total airflow entering a turbine engine combustion section, how is most of it used?
- To burn with the fuel in the primary combustion zone so combustion is complete
- To cool the combustor liner and dilute the hot gases before they reach the turbine
- To pressurize the bearing sumps and the engine's air-oil seals
Show answer
Answer: B. Only roughly a quarter of the combustor airflow takes part in burning the fuel; the rest cools the liner and mixes with the flame gases to bring them down to a temperature the turbine can tolerate. Seal pressurization uses only a small amount of bleed air.
Source: FAA-H-8083-32B, Aircraft Engines / Turbine engine combustion section
AM.III.L.K1 p4-045
On a light airplane, cabin heat comes from a shroud around the muffler. During inspection, a crack is found in the muffler inside the shroud. What is the main hazard?
- Carbon monoxide can enter the cabin with the heated air
- Engine oil can leak into the heater duct and catch fire
- Cylinder head temperatures will rise from lost back pressure
Show answer
Answer: A. The heater shroud passes outside air over the muffler and into the cabin, so a crack inside the shroud lets exhaust, including odorless carbon monoxide, mix with the heated air. Even a small crack can be dangerous. Oil leaks and head temperatures are not the defining hazard.
Source: FAA-H-8083-32B, Induction and Exhaust Systems / Reciprocating engine exhaust systems
AM.III.M.K1 p4-065
An airplane flies at 100 mph with its propeller turning 2,200 rpm. The propeller's geometric pitch is 60 inches. What is the propeller slip, as a percentage of geometric pitch?
- 20 percent
- 25 percent
- 80 percent
Show answer
Answer: A. Speed: 100 x 5,280 / 60 = 8,800 ft/min; 8,800 / 2,200 = 4 ft = 48 in effective pitch. Slip = (60 - 48) / 60 = 20 percent. Dividing 12 by the effective pitch (48) gives 25 percent, and 80 percent is the ratio of effective to geometric pitch, not slip.
Source: FAA-H-8083-32B, Propellers / Geometric pitch, effective pitch, and slip
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Are these the real FAA AMP questions?
- No. The FAA does not publish its live test questions. These are original practice items written from the FAA handbooks and regulations and tagged with the ACS code they practice.
- What score do I need?
- 70 percent on each test (14 CFR 65.17).
- Does a practice score predict my result?
- No. Use practice to find weak ACS areas. Rivetry does not publish pass rates or predictions.
Sources
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-11.
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-11.
- FAA Airman Knowledge Testing Matrix (revised September 25, 2026): AMT and IA pages. FAA. Read 2026-11-11.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-11.
- Become an Aviation Mechanic. FAA. Read 2026-11-11.
- 14 CFR 65.17, tests: general procedure (70 percent minimum passing grade). eCFR, Title 14 current as of 2026-11-09. Text read 2026-11-11.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.