A&P propellers practice questions
Propellers is ACS area AM.III.M of the FAA Powerplant (AMP) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 10 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.M.K1. Below are 6 free original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-12); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for propellers?
Propellers is a compact area with a clear logic: blade angle, how it is controlled, and what a governor does about it.
| Code | Knowledge element |
|---|---|
| AM.III.M.K1 | Propeller theory and operation. |
| AM.III.M.K2 | Types of propellers and blade design. |
| AM.III.M.K3 | Pitch control and adjustment. |
| AM.III.M.K4 | Constant speed propeller and governor theory and operation. |
| AM.III.M.K5 | Turbine engine propeller reverse/beta range operation. |
| AM.III.M.K6 | Propeller servicing, maintenance, and inspection requirements. |
| AM.III.M.K7 | Procedures for removal and installation of a propeller. |
| AM.III.M.K8 | Propeller TCDS. |
| AM.III.M.K9 | Propeller synchronization systems. |
| AM.III.M.K10 | Propeller ice control systems. |
Source: FAA-S-ACS-1, area AM.III.M, read 2026-11-12. The written test draws on the knowledge elements. The ACS also lists 2 risk management and 12 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many propellers questions will I get?
The FAA gives this area 5-10% of the AMP test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 57 reviewed items tagged AM.III.M, 6 of them free.
How should I study propellers?
- Define blade angle, pitch and angle of attack and keep them separate.
- Trace the constant speed loop: speed change, governor, oil flow to the hub, pitch change, speed returns.
- Know turbine propeller reverse and beta range (K5) as a separate topic from reciprocating propeller control.
- Study propeller inspection (K6) and the removal and installation procedures (K7), and how to use the propeller TCDS (K8).
Learn it from FAA-H-8083-32B, then test yourself.
Free mini quiz: 6 practice questions
6 free AM.III.M questions. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.M.K1 p4-066
A two-blade propeller is 6 ft in diameter and turns 2,700 rpm on the ground. What is the approximate rotational speed of the blade tips in feet per second?
- 424 ft/s
- 848 ft/s
- 1,696 ft/s
Show answer
Answer: B. Tip path per revolution = pi x diameter = 3.1416 x 6 = 18.85 ft. 18.85 x 2,700 / 60 = 848 ft/s. Using the 3 ft radius in place of the diameter gives 424 ft/s, and 2 x pi x 6 ft treats the diameter as the radius, giving 1,696 ft/s.
Source: FAA-H-8083-32B, Propellers / Propeller tip speed
AM.III.M.K1 p4-067
An engine's propeller reduction gearbox has a 3:2 ratio (engine to propeller). At an engine speed of 3,300 rpm, what is the propeller speed?
- 1,650 rpm
- 2,200 rpm
- 4,950 rpm
Show answer
Answer: B. A 3:2 engine-to-propeller ratio means the engine turns 3 times for every 2 propeller revolutions, so the propeller turns slower: 3,300 x 2 / 3 = 2,200 rpm. Multiplying by 3/2 gives 4,950 rpm, which would be an overdrive, and 1,650 rpm comes from treating the gearbox as 2:1.
Source: FAA-H-8083-32B, Propellers / Propeller reduction gearing
AM.III.M.K1 p4-068
At the 24-inch blade station of a fixed-pitch propeller, the tangent of the blade angle is 0.40. Using geometric pitch = 2 x pi x radius x tan(blade angle), what is the geometric pitch at that station?
- About 30 inches
- About 60 inches
- About 121 inches
Show answer
Answer: B. Geometric pitch = 2 x 3.1416 x 24 x 0.40 = 60.3 in. Dropping the factor of 2 (using pi x r) gives about 30 in, and using 48 in (the diameter at that station) as the radius gives about 121 in.
Source: FAA-H-8083-32B, Propellers / Geometric pitch and blade angle
AM.III.M.K1 p4-069
Of the forces acting on a rotating propeller, which one is usually the greatest and tends to pull the blades out of the hub?
- Centrifugal force
- Thrust bending force
- Torque bending force
Show answer
Answer: A. Centrifugal force acting on the blade mass is by far the largest load and tries to throw the blades out of the hub. Thrust bending bends the blades forward and torque bending bends them against the direction of rotation, but both are much smaller.
Source: FAA-H-8083-32B, Propellers / Forces acting on a propeller
AM.III.M.K1 p4-070
Which twisting moment on a rotating propeller blade tends to turn the blade toward a lower blade angle?
- Aerodynamic twisting moment
- Centrifugal twisting moment
- Thrust bending moment
Show answer
Answer: B. Centrifugal twisting moment tries to align the blade's mass with its plane of rotation, which moves it toward low pitch. Aerodynamic twisting moment acts the other way because the center of pressure is ahead of the pitch-change axis, tending to raise the blade angle.
Source: FAA-H-8083-32B, Propellers / Forces acting on a propeller
AM.III.M.K1 p4-065
An airplane flies at 100 mph with its propeller turning 2,200 rpm. The propeller's geometric pitch is 60 inches. What is the propeller slip, as a percentage of geometric pitch?
- 20 percent
- 25 percent
- 80 percent
Show answer
Answer: A. Speed: 100 x 5,280 / 60 = 8,800 ft/min; 8,800 / 2,200 = 4 ft = 48 in effective pitch. Slip = (60 - 48) / 60 = 20 percent. Dividing 12 by the effective pitch (48) gives 25 percent, and 80 percent is the ratio of effective to geometric pitch, not slip.
Source: FAA-H-8083-32B, Propellers / Geometric pitch, effective pitch, and slip
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What is a propeller TCDS?
- The type certificate data sheet for the propeller, which lists its limits and approved models; K8 names it as a knowledge element.
- Are propeller ice control systems covered?
- Yes, K10 lists propeller ice control systems.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many propellers questions does Rivetry have?
- 57 reviewed items, 6 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-12.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-12.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-12.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.