A&P reciprocating engines practice questions
Reciprocating Engines is ACS area AM.III.A of the FAA Powerplant (AMP) test, 5-15% of its 100 questions, so roughly 5 to 15 questions (FAA-G-ACS-1, chapter 3). The ACS lists 10 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.A.K1. Below are 9 free original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-12); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for reciprocating engines?
Reciprocating engines is the Powerplant area with the widest range and the one most students start with: theory, construction, performance figures and ground operation.
| Code | Knowledge element |
|---|---|
| AM.III.A.K1 | Types of reciprocating engines. |
| AM.III.A.K2 | Reciprocating engine operating principles/theory of operation. |
| AM.III.A.K3 | Internal combustion engine operating principles/theory of operation. |
| AM.III.A.K4 | Horizontally-opposed engine construction and internal components. |
| AM.III.A.K5 | Radial engine construction and internal components. |
| AM.III.A.K6 | Storage and preservation. |
| AM.III.A.K7 | Reciprocating engine performance (e.g., PLANK, SFC). |
| AM.III.A.K8 | Reciprocating engine maintenance and inspection. |
| AM.III.A.K9 | Reciprocating engine ground operations. |
| AM.III.A.K10 | Diesel engine operating principles/theory of operation. |
Source: FAA-S-ACS-1, area AM.III.A, read 2026-11-12. The written test draws on the knowledge elements. The ACS also lists 4 risk management and 9 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many reciprocating engines questions will I get?
The FAA gives this area 5-15% of the AMP test. On 100 questions that is about 5 to 15 (our arithmetic on the FAA range). Rivetry has 81 reviewed items tagged AM.III.A, 9 of them free.
How should I study reciprocating engines?
- Know the four-stroke sequence and the valve timing terms well enough to place a piston on the right stroke.
- Work the performance formulas: displacement and compression ratio, and indicated horsepower with PLANK (K7). Both have step-by-step workups.
- Compare horizontally opposed and radial construction (K4, K5) by internal components, not just shape.
- Ground operation and maintenance follow the risk elements: moving the propeller, preparing for a run-up and actions in an engine fire.
Learn it from FAA-H-8083-32B, then test yourself.
Worked calculations for this area
- Displacement and compression ratio AM.III.A.K7
- Indicated horsepower (PLANK) AM.III.A.K7
Free mini quiz: 9 practice questions
9 free AM.III.A questions. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.A.K2 p1-006
An engine's intake valve opens 20 degrees before top center and closes 55 degrees after bottom center. How many degrees of crankshaft rotation is the intake valve open?
- 215 degrees
- 235 degrees
- 255 degrees
Show answer
Answer: C. From 20 degrees BTC to top center is 20 degrees, the intake stroke from top to bottom center is 180 degrees, and the valve stays open another 55 degrees: 20 + 180 + 55 = 255 degrees. Leaving out the early opening gives 235, and subtracting it gives 215.
Source: FAA-H-8083-32B, Aircraft Engines / Valve timing
AM.III.A.K2 p1-007
What is the main benefit of having a period of valve overlap in a four-stroke aircraft engine?
- Exhaust gas momentum helps draw in the fresh charge, improving volumetric efficiency
- It lets some exhaust gas dilute the fresh charge to suppress detonation at high power
- It lowers cylinder compression pressure so the engine cranks more easily during starting
Show answer
Answer: A. With both valves open near top center, the outgoing exhaust gas creates a low pressure that helps pull the fresh charge in and scavenges the cylinder, raising volumetric efficiency. Overlap is not meant to recirculate exhaust to control detonation, and it has nothing to do with cranking effort.
Source: FAA-H-8083-32B, Aircraft Engines / Valve timing and valve overlap
AM.III.A.K2 p1-008
Why does the intake valve of an aircraft engine stay open for a time after the piston passes bottom center?
- It allows residual exhaust to escape through the intake port
- It delays compression so the spark can occur at top center
- The inertia of the incoming charge continues to fill the cylinder
Show answer
Answer: C. At high speed the fuel/air charge moving through the intake port has momentum and keeps flowing into the cylinder even as the piston starts upward, so a late closing packs in more charge. Exhaust leaving through the intake would be backfiring, and spark timing is not set by intake valve closing.
Source: FAA-H-8083-32B, Aircraft Engines / Valve timing
AM.III.A.K2 p1-009
On a four-stroke opposed engine turning 2,400 rpm, what is the speed of the camshaft?
- 1,200 rpm
- 2,400 rpm
- 4,800 rpm
Show answer
Answer: A. Each valve opens once per cycle, and a four-stroke cycle takes two crankshaft revolutions, so the camshaft is geared to turn at half crankshaft speed: 2,400 / 2 = 1,200 rpm. Running it at crankshaft speed would open every valve twice per cycle.
Source: FAA-H-8083-32B, Aircraft Engines / Opposed engine camshaft and valve operating mechanism
AM.III.A.K1 p1-001
In the engine model designation TSIO-520, what does the number 520 indicate?
- The approximate piston displacement in cubic inches
- The rated takeoff horsepower at sea level
- The maximum continuous crankshaft rpm divided by five
Show answer
Answer: A. The number in a reciprocating engine designation is its approximate total displacement in cubic inches, so a TSIO-520 displaces about 520 cu in. Rated horsepower is not part of the designation and must be taken from the type certificate data sheet.
Source: FAA-H-8083-32B, Aircraft Engines / Reciprocating engine designations
AM.III.A.K1 p1-002
An engine is listed as a GO-480. What does the letter G tell the mechanic about this engine?
- It has a gear-driven internal supercharger
- The propeller is driven through reduction gearing
- It is approved for ground-adjustable propellers only
Show answer
Answer: B. In engine designations the G stands for geared: the propeller is driven through a reduction gear so it turns slower than the crankshaft. A supercharged engine is identified by S (as in GSO-480), not by G.
Source: FAA-H-8083-32B, Aircraft Engines / Reciprocating engine designations
AM.III.A.K1 p1-003
Compared with a radial engine of similar power, why is the horizontally opposed engine favored for most light airplanes?
- It can place more cylinders on each crankpin, so the crankcase is shorter
- It needs no oil sump because it uses a dry-sump system with a separate tank
- Its small frontal area allows a low-drag installation
Show answer
Answer: C. The opposed engine is compact and flat, so its small frontal area lets it be cowled with little drag, and it has a low weight-to-horsepower ratio. Placing several cylinders on one crankpin is a radial feature, and opposed engines commonly use a wet sump.
Source: FAA-H-8083-32B, Aircraft Engines / Opposed-type engines
AM.III.A.K1 p1-004
Why are air-cooled in-line engines generally built with no more than about six cylinders?
- The crankshaft cannot be made long enough to carry more throws
- An even firing order is impossible beyond six cylinders
- The rear cylinders become difficult to cool adequately
Show answer
Answer: C. In an air-cooled in-line engine the rear cylinders sit in the wake of the front ones and receive little cooling air, which limits the practical number of cylinders. Long crankshafts and even firing orders are routine in larger engines, so neither is the limiting factor.
Source: FAA-H-8083-32B, Aircraft Engines / In-line engines
AM.III.A.K2 p1-005
A mechanic reads these valve events from an engine data plate: intake opens 20 degrees before top center, exhaust closes 15 degrees after top center. What is the valve overlap?
- 5 degrees
- 15 degrees
- 35 degrees
Show answer
Answer: C. Overlap is the period both valves are open around top center: 20 degrees before TC plus 15 degrees after TC = 35 degrees. Subtracting the two numbers (20 - 15 = 5) is the common mistake; the angles lie on opposite sides of top center, so they add.
Source: FAA-H-8083-32B, Aircraft Engines / Valve timing and valve overlap
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What does PLANK stand for?
- Pressure (mean effective pressure), Length of stroke, Area of the piston, N (power strokes per minute) and K (number of cylinders). The indicated horsepower workup shows each factor with units.
- Does this area include diesel engines?
- Yes, K10 lists diesel engine operating principles.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many reciprocating engines questions does Rivetry have?
- 81 reviewed items, 9 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-12.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-12.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-12.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.