A&P engine inspection practice questions
Engine Inspection is ACS area AM.III.C of the FAA Powerplant (AMP) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 8 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.C.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for engine inspection?
Engine inspection is the regulation side of the Powerplant test: part 43 and part 91 inspection rules, life-limited parts, ADs and service information, plus hands-on checks such as the differential compression test and engine mounts.
| Code | Knowledge element |
|---|---|
| AM.III.C.K1 | Inspection requirements under 14 CFR part 43 and 14 CFR part 91. |
| AM.III.C.K2 | Identification of life-limited parts and their replacement interval. |
| AM.III.C.K3 | Special inspections. |
| AM.III.C.K4 | Use of FAA-approved data. |
| AM.III.C.K5 | Compliance with service letters, service bulletins, instructions for continued airworthiness, ADs, or TCDSs. |
| AM.III.C.K6 | Maintenance recordkeeping requirements under 14 CFR part 43. |
| AM.III.C.K7 | Engine component inspection, checking, and servicing. |
| AM.III.C.K8 | Engine mounts, mounting hardware, and the inspection and checking of each. |
Source: FAA-S-ACS-1, area AM.III.C, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 3 risk management and 14 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many engine inspection questions will I get?
The FAA gives this area 5-10% of the AMP test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 40 reviewed items tagged AM.III.C, 4 of them free.
How should I study engine inspection?
- The differential compression test measures cylinder leakage against a calibrated orifice. Air at the exhaust points to the exhaust valve, at the intake to the intake valve, and at the crankcase breather to the rings (S1, R1).
- Track the status of every life-limited part in the records (K2).
- Engine installation eligibility comes from the type certificate data sheet or engine listing (S5, S6).
- Inspect engine mounts and hardware for cracks, especially at welds, and check the vibration isolators (K8).
Learn it from FAA-H-8083-32B, then test yourself.
What could the practical ask me to do?
These are the 14 skill elements the ACS lists for AM.III.C. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Perform a compression check on a cylinder.
- S2 Evaluate powerplant for compliance with FAA-approved or manufacturer data.
- S3 Perform a powerplant records inspection.
- S4 Inspect for compliance with applicable ADs.
- S5 Determine engine installation eligibility.
- S6 Determine compliance with engine specifications, TCDS, or engine listings.
- S7 Perform a portion of a required inspection on an engine.
- S8 Check engine controls for proper operation and adjustment.
- S9 Inspect an engine for leaks after performing maintenance.
- S10 Inspect an aircraft engine accessory for serviceability.
- S11 Inspect engine records for time or cycles on life-limited parts.
- S12 Perform an engine start and inspect engine operational parameters.
- S13 Perform a portion of a 100-hour inspection on an engine in accordance with part 43.
- S14 Inspect an engine mount to determine serviceability.
The risk management elements for this area: A compression test on a reciprocating engine (R1); Maintenance on an operating reciprocating engine (R2); Maintenance on an operating turbine engine (R3).
Free mini quiz: 5 practice questions
5 AM.III.C questions: 4 from the app's free set and 1 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.C.K1 p2-002
Under 14 CFR 43.15, before approving a reciprocating-engine airplane for return to service after a 100-hour inspection, the mechanic must run the engine to check which items against the manufacturer's recommendations?
- Cylinder compression, valve clearance, and magneto-to-engine timing on each cylinder
- Static rpm, propeller track, alternator output, and vacuum system suction
- Static and idle rpm, magnetos, fuel and oil pressure, and cylinder and oil temperatures
Show answer
Answer: C. Section 43.15(c) requires a run-up to verify power output (static and idle rpm), magnetos, fuel and oil pressure, and cylinder and oil temperature. Compression and timing are checked during the inspection itself with the engine stopped, not as the required run-up checks.
Source: 14 CFR 43.15(c)
AM.III.C.K1 p2-003
During a 100-hour inspection, the differential compression check of one cylinder comes out well below the manufacturer's limit. Under the scope of 14 CFR part 43 Appendix D, what must the inspection then include?
- A note of the low reading in the logbook and a recheck at the next scheduled inspection
- Removal of the engine and its return to the manufacturer for a complete overhaul
- A check of that cylinder for improper internal condition and tolerances
Show answer
Answer: C. Appendix D requires checking internal engine cylinder compression and, when compression is weak, checking for improper internal condition and tolerances, such as a leaking valve or worn rings. Merely recording the reading leaves a possible unairworthy condition unresolved, and a full overhaul is not automatically required.
Source: 14 CFR part 43, Appendix D
AM.III.C.K1 p2-001
An airplane that a flight school provides for flight instruction for hire was due for its 100-hour inspection at 1,200.0 hours. It was flown to 1,206.0 hours to reach the shop, where the inspection was completed. Under 14 CFR 91.409, when is the next 100-hour inspection due?
- 1,306.0 hours
- 1,300.0 hours
- 1,310.0 hours
Show answer
Answer: B. The 100-hour limit may be exceeded by up to 10 hours only to reach a place where the inspection can be done, and the excess time counts toward the next interval: 1,200 + 100 = 1,300 hours. Counting from 1,206 to 1,306 wrongly gives credit for the 6 hours flown past the due point.
Source: 14 CFR 91.409(b)
AM.III.C.K1 p2-004
Under 14 CFR 65.95, what additional authority must a certificated mechanic hold to perform an annual inspection and approve the aircraft for return to service?
- An inspection authorization
- A repairman certificate for that make of aircraft
- Airframe and powerplant ratings used within the preceding 24 months
Show answer
Answer: A. Section 65.95 gives the holder of an inspection authorization the privilege to perform annual inspections and approve the aircraft for return to service. A mechanic with airframe and powerplant ratings and current recent experience may do 100-hour inspections but not approve an annual.
Source: 14 CFR 65.95; 14 CFR 43.7
AM.III.C.K2 p2-005
How are the life limits of turbine engine rotating parts such as compressor and turbine disks usually expressed?
- In cycles, since each start and stop adds a fatigue stress cycle
- In calendar months since the engine's last overhaul or hot section inspection
- In hours operated above maximum continuous power
Show answer
Answer: A. Disk life is limited mainly by low-cycle fatigue from each acceleration to high rpm and back, so limits are set in cycles (sometimes with hours as well). Calendar time and time at high power do not measure the stress reversals that actually consume disk life.
Source: FAA-H-8083-32B, Aircraft Engines / Turbine engine life-limited parts; 14 CFR 91.417(a)(2)(ii)
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Why is the compression test a risk element?
- Pressurizing a cylinder can turn the propeller, so the test is done with the propeller held and people clear (R1).
- How does this differ from airframe inspection?
- The rules are the same (parts 43 and 91, ADs), but the hands-on checks are engine specific.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many engine inspection questions does Rivetry have?
- 40 reviewed items, 4 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.