A&P engine exhaust and reverser systems practice questions

Engine Exhaust and Reverser Systems is ACS area AM.III.L of the FAA Powerplant (AMP) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 4 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.L.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.

Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.

What does the ACS list for engine exhaust and reverser systems?

Engine exhaust and reverser systems covers reciprocating and turbine exhaust, noise suppression and thrust reversers. It has four knowledge elements, and exhaust leaks are among the most safety-critical findings a mechanic makes.

CodeKnowledge element
AM.III.L.K1Reciprocating engine exhaust system theory, components, operation, and inspection.
AM.III.L.K2Turbine engine exhaust system theory, components, operation, and inspection.
AM.III.L.K3Noise suppression theory, components, and operation (e.g., mufflers, hush kits, augmenter tubes).
AM.III.L.K4Thrust reverser theory, components, and operation.

Source: FAA-S-ACS-1, area AM.III.L, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 5 risk management and 7 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).

How many engine exhaust and reverser systems questions will I get?

The FAA gives this area 5-10% of the AMP test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 36 reviewed items tagged AM.III.L, 4 of them free.

How should I study engine exhaust and reverser systems?

Learn it from FAA-H-8083-32B, then test yourself.

What could the practical ask me to do?

These are the 7 skill elements the ACS lists for AM.III.L. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).

The risk management elements for this area: Maintenance and inspection of exhaust system components (R1); Operation of turbine engine reversing systems (R2); Operation of reciprocating engines with exhaust systems leaks (R3); Exhaust system failures (R4); Ground operation of aircraft engines (R5).

Free mini quiz: 5 practice questions

5 AM.III.L questions: 4 from the app's free set and 1 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.

  1. AM.III.L.K1 p4-046

    A mechanic must mark an area on a stainless steel exhaust stack that needs further inspection. Which marking method is acceptable?

    1. Chalk or a marking material approved for exhaust system parts
    2. A soft lead pencil, because the graphite burns off cleanly in operation
    3. A steel scribe, so the mark is not lost when the stack gets hot
    Show answer

    Answer: A. Lead pencil or graphite marks can be absorbed into the metal when heated, changing its structure and leading to cracks, so they must never be used on exhaust parts. A scribed line creates a stress riser. Use chalk or an approved marker.

    Source: FAA-H-8083-32B, Induction and Exhaust Systems / Exhaust system inspection

  2. AM.III.L.K1 p4-047

    During a 100-hour inspection, a mechanic finds a flat gray, sooty streak on the cowling next to an exhaust pipe joint. What does it most likely indicate?

    1. Oil is leaking from a nearby rocker cover
    2. The cylinder at that joint is running too lean
    3. Exhaust gas is leaking at that joint
    Show answer

    Answer: C. Exhaust leaks typically leave flat gray or sooty black streaks at the leaking joint or crack, so the joint and its clamp or gasket must be checked. An oil leak leaves a wet, brown film, and a lean mixture leaves no streak on the cowling.

    Source: FAA-H-8083-32B, Induction and Exhaust Systems / Exhaust system inspection

  3. AM.III.L.K1 p4-048

    Why are some joints in a reciprocating engine exhaust system made as slip joints or ball joints instead of rigid welded connections?

    1. To let the stacks be removed without disturbing the cylinder flanges
    2. To bleed off some exhaust pressure and reduce back pressure
    3. To allow for thermal expansion and contraction without cracking
    Show answer

    Answer: C. Exhaust parts expand and contract greatly with temperature; slip and ball joints let them move so stresses do not crack the pipes. They are not designed to vent pressure; a leaking joint is a defect.

    Source: FAA-H-8083-32B, Induction and Exhaust Systems / Reciprocating engine exhaust systems

    Get Rivetry on Google Play

  4. AM.III.L.K1 p4-045

    On a light airplane, cabin heat comes from a shroud around the muffler. During inspection, a crack is found in the muffler inside the shroud. What is the main hazard?

    1. Carbon monoxide can enter the cabin with the heated air
    2. Engine oil can leak into the heater duct and catch fire
    3. Cylinder head temperatures will rise from lost back pressure
    Show answer

    Answer: A. The heater shroud passes outside air over the muffler and into the cabin, so a crack inside the shroud lets exhaust, including odorless carbon monoxide, mix with the heated air. Even a small crack can be dangerous. Oil leaks and head temperatures are not the defining hazard.

    Source: FAA-H-8083-32B, Induction and Exhaust Systems / Reciprocating engine exhaust systems

  5. AM.III.L.K1 p4-049

    A pilot reports a gradual loss of power that has worsened over several flights. The mechanic finds that a loose internal baffle has partly blocked the muffler outlet. Why does this reduce power?

    1. The blockage raises back pressure and keeps the cylinders from expelling exhaust
    2. The baffle lets cold air back into the cylinders through the exhaust valves
    3. The blockage leans the mixture by reducing the vacuum at the carburetor venturi
    Show answer

    Answer: A. Internal muffler failures can restrict exhaust flow, raising back pressure so exhaust gases are not fully expelled, which can cause partial or even complete loss of power. The blockage has no direct effect on carburetor venturi metering.

    Source: FAA-H-8083-32B, Induction and Exhaust Systems / Muffler and exhaust system failures

Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.

Get Rivetry on Google Play

More questions

How is a piston engine exhaust checked for leaks?
S7 lists a pressure leak check of the exhaust system, alongside visual inspection.
Are reversers operated on the ground?
Operating turbine reversing systems is risk element R2. Follow the manufacturer's procedure and keep the area clear.
Are these the real FAA questions?
No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
How many engine exhaust and reverser systems questions does Rivetry have?
36 reviewed items, 4 of them free.

Sources

Related guides

General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.