A&P engine fuel and fuel metering systems practice questions
Engine Fuel and Fuel Metering Systems is ACS area AM.III.I of the FAA Powerplant (AMP) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 16 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.I.K1. Below are 6 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for engine fuel and fuel metering systems?
Engine fuel and fuel metering is a heavy Powerplant area: carburetor theory, float and pressure carburetors, continuous-flow fuel injection, turbine fuel controls (hydromechanical and FADEC), nozzles, pumps, valves, filters and drains.
| Code | Knowledge element |
|---|---|
| AM.III.I.K1 | Fuel/air ratio and fuel metering, and carburetor theory and operation. |
| AM.III.I.K2 | Float carburetor theory, components, operation, and adjustment. |
| AM.III.I.K3 | Pressure carburetor theory, operation, and adjustment. |
| AM.III.I.K4 | Continuous-flow fuel injection theory, components, operation, troubleshooting and adjustment. |
| AM.III.I.K5 | Digital engine control module (e.g., FADEC). |
| AM.III.I.K6 | Hydromechanical fuel control system design and components. |
| AM.III.I.K7 | Fuel nozzles and manifolds design, operation, and maintenance. |
| AM.III.I.K8 | Components, theory, and operation of turbine engine fuel metering system. |
| AM.III.I.K9 | Inspection requirements for an engine fuel system. |
| AM.III.I.K10 | Fuel system operation. |
| AM.III.I.K11 | Fuel heaters. |
| AM.III.I.K12 | Fuel lines. |
| AM.III.I.K13 | Fuel pumps. |
| AM.III.I.K14 | Fuel valves. |
| AM.III.I.K15 | Fuel filters. |
| AM.III.I.K16 | Engine fuel drains. |
Source: FAA-S-ACS-1, area AM.III.I, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 5 risk management and 30 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many engine fuel and fuel metering systems questions will I get?
The FAA gives this area 5-10% of the AMP test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 51 reviewed items tagged AM.III.I, 6 of them free.
How should I study engine fuel and fuel metering systems?
- In a float carburetor the pressure drop in the venturi draws fuel from the main jet. Learn its systems: idle, main metering, accelerating, mixture control and power enrichment (K2).
- Fuel/air ratio is by weight, and the best-power mixture is richer than the best-economy mixture (K1).
- Continuous-flow fuel injection meters fuel by airflow and sprays it continuously at the intake ports (K4).
- Turbine fuel controls schedule fuel from inputs such as power lever position, engine speed, pressure and temperature (K6, K8).
Learn it from FAA-H-8083-32B, then test yourself.
What could the practical ask me to do?
These are the 30 skill elements the ACS lists for AM.III.I. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Inspect, troubleshoot, and repair a continuous-flow fuel injection system.
- S2 Remove, inspect, and install a turbine engine fuel nozzle.
- S3 Identify carburetor components.
- S4 Identify fuel and air flow through a float-type carburetor.
- S5 Remove and install a carburetor main metering jet.
- S6 Inspect a carburetor fuel inlet screen.
- S7 Adjust a continuous-flow fuel injection system.
- S8 Inspect the needle, seat, and float level on a float-type carburetor.
- S9 Remove and install a float-type carburetor.
- S10 Adjust carburetor idle speed and mixture.
- S11 Locate procedures for a turbine engine revolutions per minute (rpm) overspeed inspection.
- S12 Inspect fuel metering cockpit controls for proper adjustment.
- S13 Locate procedures for adjusting a hydromechanical fuel control unit.
- S14 Locate and explain procedures for removing and installing a turbine engine fuel control unit.
- S15 Identify components of an engine fuel system.
- S16 Remove and install an engine-driven fuel pump.
- S17 Inspect a remotely-operated fuel valve for proper operation.
- S18 Locate and identify fuel selector placards.
- S19 Inspect a main fuel filter assembly for leaks.
- S20 Inspect fuel boost pump.
- S21 Locate and identify a turbine engine fuel heater.
- S22 Inspect fuel pressure warning light function.
- S23 Adjust fuel pump fuel pressure.
- S24 Inspect engine fuel system fluid lines and components.
- S25 Troubleshoot abnormal fuel pressure.
- S26 Locate the procedures for troubleshooting a turbine engine fuel heater system.
- S27 Remove, clean, and reinstall an engine fuel filter.
- S28 Troubleshoot engine fuel pressure fluctuation.
- S29 Inspect fuel selector valve.
- S30 Determine correct fuel nozzle spray pattern.
The risk management elements for this area: Adjusting a turbine engine fuel control (R1); Adjusting reciprocating engine fuel control systems (R2); Handling of fuel metering system components that may contain fuel (R3); Considerations during fuel system maintenance (R4); Handling of engine fuel control units that may contain fuel (R5).
Free mini quiz: 6 practice questions
6 AM.III.I questions: 6 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.I.K1 p3-070
If the mixture is not adjusted, what happens to the fuel/air mixture from a float carburetor as the airplane climbs?
- It becomes leaner, because the lower air pressure reduces fuel flow from the float chamber
- It becomes richer, because the air is less dense but fuel flow is not reduced to match
- It stays the same, because the venturi automatically adjusts for air density
Show answer
Answer: B. The carburetor meters by air volume through the venturi, so as density drops each cubic foot of air weighs less while fuel flow stays nearly the same, and the mixture richens. That is why the pilot leans with altitude. A basic float carburetor has no automatic density compensation.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Carburetor theory, mixture and altitude
AM.III.I.K1 p3-071
During a run-up, applying carburetor heat causes a small, steady rpm drop. What causes this drop?
- Less dense heated air lowers power and richens the mixture
- The heated air leans the mixture until the engine begins to run rough
- The drop shows that carburetor ice is already forming in the venturi
Show answer
Answer: A. Carburetor heat brings in warm, unfiltered air of lower density; less air mass means less power, and the same fuel metered into thinner air richens the mixture. If ice were present, rpm would usually drop and then rise as the ice melted, and heated air richens rather than leans.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Carburetor heat and icing
AM.III.I.K2 p3-072
A float carburetor's float level is found set higher than specified. What effect does this have?
- A leaner mixture, with possible fuel starvation at full throttle
- No change, because the main metering jet alone sets fuel flow
- A richer mixture, with possible fuel drip from the nozzle at rest
Show answer
Answer: C. A higher fuel level lowers the pressure drop needed to lift fuel to the nozzle, so more fuel flows at any airflow and the mixture runs rich; if high enough, fuel can run out of the nozzle when the engine is stopped. A low float level, not a high one, would lean the mixture.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Float carburetors, float level
AM.III.I.K2 p3-073
An engine with a float carburetor stumbles when the throttle is opened quickly but runs smoothly when the throttle is opened slowly. Which carburetor system is the likely cause?
- The idle mixture adjustment
- The accelerating pump
- The economizer (power enrichment) system
Show answer
Answer: B. When the throttle opens quickly, airflow increases faster than fuel can follow, so the accelerating pump squirts extra fuel to prevent a momentary lean stumble. The economizer adds fuel at high power settings, not during sudden throttle movement, and idle mixture affects only idle operation.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Float carburetors, accelerating system
AM.III.I.K3 p3-075
Why is a pressure injection carburetor much less prone to fuel-evaporation icing than a float carburetor?
- It heats the fuel before metering so that moisture in the fuel cannot freeze
- It vents its float chamber to warm engine-compartment air behind the firewall
- It sprays fuel under pressure past the throttle valve, not in the venturi
Show answer
Answer: C. In a float carburetor, fuel vaporizes at the venturi and throttle, where the cooling can freeze moisture on those parts. A pressure carburetor discharges fuel under pressure past the throttle valve, so that cooling does not occur where ice can block the airflow. It has no float chamber, and its fuel is not heated.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Pressure carburetors
AM.III.I.K1 p3-069
An engine burns 12.5 gallons of avgas per hour (6 pounds per gallon) while consuming 1,000 pounds of air per hour. What is its fuel/air ratio?
- 13.3
- 0.075
- 0.0125
Show answer
Answer: B. Fuel flow is 12.5 gal/hr x 6 lb/gal = 75 lb/hr, and the fuel/air ratio is 75 / 1,000 = 0.075 (about 1:13.3). Using gallons instead of pounds gives 12.5 / 1,000 = 0.0125, and 13.3 is the air/fuel ratio (1,000 / 75), the inverse of what was asked.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Fuel/air mixtures
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What is a stoichiometric mixture?
- The chemically correct mixture, about 15 parts air to 1 part fuel by weight for gasoline.
- Is FADEC in more than one area?
- Yes: here (K5), in ignition and starting (AM.III.H.K6) and in engine instruments (AM.III.D.K9).
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many engine fuel and fuel metering systems questions does Rivetry have?
- 51 reviewed items, 6 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.