A&P engine instrument systems practice questions
Engine Instrument Systems is ACS area AM.III.D of the FAA Powerplant (AMP) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 11 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.D.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for engine instrument systems?
Engine instrument systems covers how fuel flow, temperatures, speeds and pressures are sensed and displayed, from thermocouples and tachometers to EPR, torquemeters, EICAS, ECAM and FADEC.
| Code | Knowledge element |
|---|---|
| AM.III.D.K1 | Fuel flow. |
| AM.III.D.K2 | Temperature (e.g., exhaust gas, oil, oil cylinder head, turbine inlet). |
| AM.III.D.K3 | Engine speed indicating systems. |
| AM.III.D.K4 | Pressure (e.g., air, fuel, manifold, oil). |
| AM.III.D.K5 | Annunciator indicating systems (e.g., warning, caution, and advisory lights). |
| AM.III.D.K6 | Torquemeters. |
| AM.III.D.K7 | Engine pressure ratio (EPR). |
| AM.III.D.K8 | Engine indicating and crew alerting system (EICAS). |
| AM.III.D.K9 | Digital engine control module (e.g., full authority digital engine controls (FADEC)). |
| AM.III.D.K10 | Electronic centralized aircraft monitor (ECAM). |
| AM.III.D.K11 | Engine instrument range markings and instrument conditions. |
Source: FAA-S-ACS-1, area AM.III.D, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 2 risk management and 19 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many engine instrument systems questions will I get?
The FAA gives this area 5-10% of the AMP test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 40 reviewed items tagged AM.III.D, 4 of them free.
How should I study engine instrument systems?
- Thermocouples make their own voltage. The leads are a calibrated resistance and must not be cut or shortened (K2, S8).
- Manifold pressure is the absolute pressure in the intake manifold, shown in inches of mercury (K4).
- EPR compares turbine discharge pressure with compressor inlet pressure as a measure of thrust (K7).
- Engine instrument range markings follow the same colors as other instruments (K11).
Learn it from FAA-H-8083-32B, then test yourself.
What could the practical ask me to do?
These are the 19 skill elements the ACS lists for AM.III.D. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Troubleshoot an engine oil temperature/pressure instrument system.
- S2 Troubleshoot a low fuel pressure indicating system.
- S3 Remove, inspect, and install a fuel-flow transmitter.
- S4 Remove, inspect, and install fuel-flow gauge.
- S5 Identify components of an electric tachometer system.
- S6 Check fuel-flow transmitter power supply.
- S7 Inspect tachometer markings for accuracy.
- S8 Perform resistance measurements of thermocouple indication system.
- S9 Remove, inspect, and install turbine engine exhaust gas temperature (EGT) component.
- S10 Locate procedures for troubleshooting a turbine EPR system.
- S11 Troubleshoot a tachometer system.
- S12 Replace a cylinder head temperature thermocouple.
- S13 Inspect EGT probes.
- S14 Locate and inspect engine low fuel pressure warning system components.
- S15 Check aircraft engine manifold pressure gauge for proper operation.
- S16 Inspect a manifold pressure system.
- S17 Repair a low oil pressure warning system.
- S18 Troubleshoot an EGT indicating system.
- S19 Inspect an oil temperature probe.
The risk management elements for this area: Maintenance damage to the instrument or indicating system (R1); Engine instrument calibration or instrument error (R2).
Free mini quiz: 5 practice questions
5 AM.III.D questions: 4 from the app's free set and 1 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.D.K1 p2-028
Why are turbine engine fuel flow indicators usually calibrated in pounds per hour rather than gallons per hour?
- Jet fuel is too viscous for volume-type flowmeters to measure it accurately
- Pounds per hour reads directly as the engine's thrust output in pounds
- The fuel's heat energy depends on its mass, not on its changing volume
Show answer
Answer: C. Fuel density changes with temperature, so a gallon carries different energy at different temperatures, while a pound of fuel always has about the same heat content. Mass flow therefore reflects engine power more accurately. Fuel flow in pounds per hour is not the same as thrust.
Source: FAA-H-8083-32B, Aircraft Engines / Turbine engine instruments, fuel flow
AM.III.D.K1 p2-029
A turboprop begins a flight with 2,400 lb of fuel set on the totalizer and burns a steady 650 lb/hr for 1 hour 30 minutes. If the totalizer is working correctly, what fuel remaining should it show?
- 1,555 lb
- 1,425 lb
- 1,750 lb
Show answer
Answer: B. Fuel used is 650 x 1.5 = 975 lb, so 2,400 - 975 = 1,425 lb remain. Entering 1 hour 30 minutes as 1.3 hours gives 845 lb used and 1,555 lb, and using only one hour gives 1,750 lb.
Source: FAA-H-8083-32B, Aircraft Engines / Turbine engine instruments, fuel flow and totalizer
AM.III.D.K2 p2-030
While tidying an engine compartment, a mechanic finds a cylinder head temperature thermocouple lead longer than needed and plans to cut it shorter. Why should this not be done?
- Thermocouple voltage is produced along the lead, so a shorter lead gives too little voltage
- The lead resistance is part of the calibrated circuit, so shortening it causes an indicating error
- Cutting the lead reverses the thermocouple polarity, so the gauge reads backward
Show answer
Answer: B. The indicator is a millivoltmeter calibrated for a specific external circuit resistance, so the leads are made to a set length or resistance and must not be cut. The voltage comes from the junction temperature difference, not from lead length, and cutting does not reverse polarity.
Source: FAA-H-8083-31B, Aircraft Instrument Systems / Thermocouple temperature indicators
AM.III.D.K1 p2-027
On a fuel-injected engine whose fuel flow indicator actually senses fuel pressure at the flow divider, the gauge shows higher than normal flow at a given power setting. What is the most likely cause?
- A leaking nozzle line downstream of the flow divider
- An air leak in the induction manifold
- One or more partly clogged injector nozzles
Show answer
Answer: C. Because this indicator is a pressure gauge calibrated in fuel flow, a restricted nozzle raises the pressure and the gauge shows more flow even though less fuel reaches that cylinder. A leaking line lowers the pressure and gives a low reading.
Source: FAA-H-8083-32B, Engine Fuel and Fuel Metering Systems / Fuel-injection flow indication
AM.III.D.K2 p2-031
Which thermocouple materials are normally used for turbine exhaust gas temperature probes because they withstand higher temperatures?
- Iron and constantan
- Copper and constantan
- Chromel and alumel
Show answer
Answer: C. Chromel-alumel thermocouples handle the high temperatures in a turbine exhaust or interstage section. Iron-constantan is common for reciprocating engine cylinder head temperature, and copper-constantan is suited to lower temperatures.
Source: FAA-H-8083-31B, Aircraft Instrument Systems / Thermocouple temperature indicators
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What does a torquemeter show?
- The torque delivered by a turboprop or turboshaft engine, used to set power (K6).
- Are EICAS and ECAM both tested?
- Yes. Both are knowledge elements (K8, K10).
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many engine instrument systems questions does Rivetry have?
- 40 reviewed items, 4 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.