A&P ignition and starting systems practice questions
Ignition and Starting Systems is ACS area AM.III.H of the FAA Powerplant (AMP) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 9 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.III.H.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for ignition and starting systems?
Ignition and starting systems covers magnetos and their three circuits, spark plugs, impulse couplings and shower of sparks, solid-state and turbine ignition, FADEC and starters.
| Code | Knowledge element |
|---|---|
| AM.III.H.K1 | Ignition system theory. |
| AM.III.H.K2 | Spark plug theory. |
| AM.III.H.K3 | Shower of sparks and impulse coupling. |
| AM.III.H.K4 | Three electrical circuits of a magneto system. |
| AM.III.H.K5 | Solid-state ignition systems. |
| AM.III.H.K6 | Digital engine control module (e.g., FADEC). |
| AM.III.H.K7 | Engine starters. |
| AM.III.H.K8 | Magneto system components and operation. |
| AM.III.H.K9 | Turbine engine ignition systems. |
Source: FAA-S-ACS-1, area AM.III.H, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 3 risk management and 17 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many ignition and starting systems questions will I get?
The FAA gives this area 5-10% of the AMP test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 50 reviewed items tagged AM.III.H, 5 of them free.
How should I study ignition and starting systems?
- The three magneto circuits are the magnetic, the primary electrical and the secondary electrical circuit (K4).
- Impulse couplings and shower of sparks systems give a strong, retarded spark for starting (K3).
- A magneto with a broken P-lead is hot. Treat the propeller as if the engine could fire (R3).
- Turbine ignition uses high-energy capacitor discharge units that can hold a lethal charge (K9, R2).
Learn it from FAA-H-8083-32B, then test yourself.
What could the practical ask me to do?
These are the 17 skill elements the ACS lists for AM.III.H. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Set magneto internal timing.
- S2 Time magneto to engine.
- S3 Remove, clean, and install spark plug.
- S4 Troubleshoot and repair an ignition system.
- S5 Inspect an electrical starting system.
- S6 Inspect magneto breaker points.
- S7 Inspect an ignition harness.
- S8 Inspect a magneto impulse coupling.
- S9 Troubleshoot an electrical starting system.
- S10 Troubleshoot ignition switch circuit.
- S11 Inspect and check gap of spark plugs.
- S12 Identify the correct spark plugs used for replacement installation.
- S13 Troubleshoot a turbine or reciprocating engine ignition system.
- S14 Identify the correct igniter plug and replace turbine engine igniter plugs.
- S15 Troubleshoot turbine engine igniters.
- S16 Inspect turbine engine ignition system.
- S17 Inspect igniters.
The risk management elements for this area: Advanced and retarded ignition timing (piston engine) (R1); Maintenance on engines with capacitor discharge ignition systems (R2); Working around reciprocating engines with an ungrounded magneto (R3).
Free mini quiz: 5 practice questions
5 AM.III.H questions: 5 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.III.H.K1 p3-033
Which condition is most likely if a magneto is timed too far advanced?
- Backfiring through the induction system during acceleration
- High exhaust gas temperatures with afterfiring in the exhaust
- High cylinder head temperatures and detonation
Show answer
Answer: C. With the spark too early, pressure peaks before or near top center, raising cylinder temperature and the risk of detonation. Late (retarded) timing leaves the charge burning into the exhaust, giving high exhaust temperature and power loss, while induction backfiring is typical of a lean mixture.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Ignition timing
AM.III.H.K1 p3-034
A spark plug's electrodes have eroded until the gap is well beyond limits. When is this plug most likely to misfire?
- At high manifold pressure, such as during takeoff
- Only during cranking, when magneto speed is lowest
- At idle, when cylinder pressures are lowest
Show answer
Answer: A. The voltage needed to jump a gap rises with both gap width and the density of the charge between the electrodes. At high manifold pressure, compression pressure is highest, so a wide gap may need more voltage than the system can supply. At idle the pressure is low, so the same gap may still fire.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Spark plug gap and firing voltage
AM.III.H.K2 p3-035
A plug with a hotter heat range than specified is installed in a high-compression engine. What is the main risk?
- Lead and carbon fouling because the plug never gets hot enough
- A weak spark because the magneto cannot fire a hot plug
- Preignition from an overheated insulator tip or electrodes
Show answer
Answer: C. A hot plug has a long insulator path that holds heat; in a hot-running engine its tip can glow and ignite the charge before the spark. Fouling from a plug that runs too cool is the problem with a plug that is too cold, and heat range does not affect magneto output.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Spark plug heat range
AM.III.H.K2 p3-036
A training fleet's engines spend most of their time at low power, and the plugs keep fouling. The approved plug list includes hotter and colder plugs for this engine. Which change is most likely to help?
- Install an approved plug with a hotter heat range
- Install an approved plug with a colder heat range
- Install the approved plug with the longest reach available
Show answer
Answer: A. A hotter plug keeps the insulator nose warm enough to burn off deposits in a cool-running engine, reducing fouling. A colder plug would run cooler still and foul sooner. Reach is set by the cylinder bushing and must match the engine, not be chosen to cure fouling.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Spark plug heat range
AM.III.H.K1 p3-031
Why do certificated aircraft piston engines normally have two spark plugs in each cylinder?
- Two plugs share the firing voltage, so each plug needs only half as much
- One plug fires on the compression stroke and the other on the exhaust stroke
- Two flame fronts speed combustion, and one system backs up the other
Show answer
Answer: C. Dual ignition gives two flame fronts for quicker, more complete combustion and provides redundancy if one magneto or its leads fail. Both plugs fire near the end of the compression stroke, and each plug still needs the full firing voltage.
Source: FAA-H-8083-32B, Engine Ignition and Electrical Systems / Dual ignition
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What is the difference between internal and external magneto timing?
- Internal timing sets the points to open at the E-gap position inside the magneto; external timing sets the magneto to fire at the correct crankshaft position (S1, S2).
- Are starters here?
- Yes. Engine starters are K7, and direct-drive starters also appear in the engine electrical skills.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many ignition and starting systems questions does Rivetry have?
- 50 reviewed items, 5 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-32B, Aviation Maintenance Technician Handbook: Powerplant. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.