A&P flight controls practice questions
Flight Controls is ACS area AM.II.C of the FAA Airframe (AMA) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 13 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.II.C.K1. Below are 6 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for flight controls?
Flight controls covers the hardware that moves the surfaces (cables, pulleys, guides, push-pull tubes, torque tubes and bellcranks), how it is rigged and checked, and why control surfaces must stay balanced.
| Code | Knowledge element |
|---|---|
| AM.II.C.K1 | Control cables. |
| AM.II.C.K2 | Control cable maintenance. |
| AM.II.C.K3 | Cable connectors. |
| AM.II.C.K4 | Cable guides. |
| AM.II.C.K5 | Control stops. |
| AM.II.C.K6 | Push-pull tubes. |
| AM.II.C.K7 | Torque tubes. |
| AM.II.C.K8 | Bellcranks. |
| AM.II.C.K9 | Flutter and flight control balance. |
| AM.II.C.K10 | Rigging of aircraft flight controls. |
| AM.II.C.K11 | Aircraft flight controls and stabilizer systems. |
| AM.II.C.K12 | Other aerodynamic wing features. |
| AM.II.C.K13 | Secondary and auxiliary control surfaces. |
Source: FAA-S-ACS-1, area AM.II.C, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 5 risk management and 13 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many flight controls questions will I get?
The FAA gives this area 5-10% of the AMA test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 51 reviewed items tagged AM.II.C, 6 of them free.
How should I study flight controls?
- Cable tension changes with temperature, so the rigging chart gives a tension for the ambient temperature. Read it together with the tensiometer's own calibration chart (K2, R1, R5).
- Rigging checks cover neutral position, cable tension, surface travel and the control stops, all against the manufacturer's figures (K5, K10).
- An unbalanced surface can flutter. After a repair or repainting, check the balance the way the manufacturer specifies (K9, S8).
- Know the axes: ailerons roll the airplane about the longitudinal axis, the elevator pitches it about the lateral axis, and the rudder yaws it about the vertical axis (S2).
Learn it from FAA-H-8083-31B, then test yourself.
What could the practical ask me to do?
These are the 13 skill elements the ACS lists for AM.II.C. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Identify fixed-wing aircraft rigging adjustment locations.
- S2 Identify control surfaces that provide movement about an aircraft's axes.
- S3 Inspect a primary and secondary flight control surface.
- S4 Remove and reinstall a primary flight control surface.
- S5 Inspect primary control cables.
- S6 Adjust and secure a primary flight control cable.
- S7 Adjust push-pull flight control systems.
- S8 Check the balance of a flight control surface.
- S9 Determine allowable axial play limits for a flight control bearing.
- S10 Inspect a trim tab for freeplay, travel, and operation.
- S11 Balance a control surface.
- S12 Fabricate a primary flight control cable.
- S13 Locate aircraft flight control travel limits.
The risk management elements for this area: Use of and interpretation of a cable tension chart (R1); Rigging aircraft flight controls (R2); Selection and use of lifting equipment used to move aircraft components into place for assembly (R3); Maintaining a calibration schedule for cable tension meters and other rigging equipment (R4); Use and interpretation of cable tensiometers (R5).
Free mini quiz: 6 practice questions
6 AM.II.C questions: 6 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.II.C.K1 a2-003
A mechanic replacing a damaged 1/8-inch 7 x 19 aileron cable finds only 1/8-inch 7 x 7 cable in stock. Why should the 7 x 7 cable not be substituted?
- It is too stiff to accept the standard swaged terminal fittings
- Its fewer, thicker wires fatigue and break sooner when bent over the pulleys
- It stretches more under load, so it can never be brought to rigging tension
Show answer
Answer: B. Each strand of 7 x 7 cable has only 7 relatively thick wires, so repeated bending over pulleys fatigues them faster than the 19 fine wires of 7 x 19 cable. 7 x 7 cable takes swaged terminals normally, and it is stiffer, not stretchier, than 7 x 19 cable.
Source: FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Control cable construction
AM.II.C.K2 a2-004
What is a practical way to find individual broken wires along a control cable during an inspection?
- Measure the cable tension and look for a low reading
- Look for bright, shiny spots on the cable surface
- Wipe a cloth along the cable and note where it snags
Show answer
Answer: C. Broken wire ends stick out and catch the fibers of a cloth drawn along the cable, pointing to damage that may be too small to see easily. A tension reading shows rigging, not broken wires. Shiny spots are a sign of wear against something, which is worth checking, but they do not locate broken wires.
Source: FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Cable inspection
AM.II.C.K2 a2-005
An all-metal airplane's control cables are rigged to the specified tension in a 70 degF hangar. With no tension regulators installed, what happens to the cable tension when the airplane is cold-soaked at -20 degF?
- It decreases, because the aluminum structure shrinks more than the steel cables
- It increases, because the steel cables shrink more than the aluminum structure
- It stays the same, because the steel and aluminum shrink by equal amounts
Show answer
Answer: A. Aluminum alloy has roughly twice the coefficient of expansion of steel, so in the cold the airframe shortens more than the cables and the cables go slack. That is why rigging charts give tension by temperature and why some airplanes use tension regulators. Steel does not shrink more than aluminum, so tension does not rise.
Source: FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Cable tension and temperature
AM.II.C.K2 a2-006
During an annual inspection a mechanic finds external corrosion on a section of steel control cable. What should be done next?
- Clean the surface and coat the cable with grease, then return it to service
- Relieve the tension and open the strands to check for internal corrosion
- Polish the corrosion away with abrasive cloth and recheck the tension
Show answer
Answer: B. Surface corrosion may hide corrosion between the strands, so the cable is slackened and twisted open to look inside; a cable with internal corrosion must be replaced. Cleaning and coating is acceptable only after confirming there is no internal corrosion. Abrasives and metallic wool damage the wires and are not used to clean control cables.
Source: AC 43.13-1B, Chapter 7, Aircraft Hardware, Control Cables, and Turnbuckles; FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Cable inspection
AM.II.C.K3 a2-007
After a turnbuckle has been adjusted, what is the maximum number of threads that may be exposed outside the barrel at either end?
- Three threads
- Five threads
- No threads at all
Show answer
Answer: A. A properly adjusted turnbuckle shows no more than three threads outside the barrel at each end, which ensures enough thread engagement inside it. More exposed threads mean too little engagement. Some threads may show; the limit is three, not zero.
Source: AC 43.13-1B, Chapter 7, Aircraft Hardware, Control Cables, and Turnbuckles; FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Turnbuckles
AM.II.C.K1 a2-002
What is the smallest diameter of steel cable that should be used in a primary flight control system?
- 1/16 inch
- 3/32 inch
- 1/8 inch
Show answer
Answer: C. Primary control cables should be no smaller than 1/8 inch in diameter, which gives the strength and wear margin needed for elevator, aileron and rudder runs. Smaller sizes such as 1/16 or 3/32 inch appear in trim tab, light secondary, or nonflight control runs but are below the primary-control minimum.
Source: AC 43.13-1B, Chapter 7, Aircraft Hardware, Control Cables, and Turnbuckles; FAA-H-8083-31B, Aircraft Structural Assembly and Rigging / Cable types
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- How is a turnbuckle checked?
- No more than three threads exposed on either side of the barrel, then it is safetied with wire or clips. The FAA Airframe handbook and AC 43.13-1B give the method.
- Are helicopter controls in this area?
- No. Rotorcraft controls are in rotorcraft fundamentals, AM.II.N.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many flight controls questions does Rivetry have?
- 51 reviewed items, 6 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.