A&P environmental systems practice questions
Environmental Systems is ACS area AM.II.G of the FAA Airframe (AMA) test, 5-10% of its 100 questions, so roughly 5 to 10 questions (FAA-G-ACS-1, chapter 3). The ACS lists 10 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.II.G.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for environmental systems?
Environmental systems covers heating, cooling, pressurization and oxygen: exhaust heat exchangers and combustion heaters on light aircraft, vapor-cycle and air-cycle air conditioning, cabin pressure control, and oxygen equipment.
| Code | Knowledge element |
|---|---|
| AM.II.G.K1 | Pressurization systems. |
| AM.II.G.K2 | Bleed air heating. |
| AM.II.G.K3 | Aircraft instrument cooling. |
| AM.II.G.K4 | Exhaust heat exchanger and system component(s) function, operation, and inspection procedures. |
| AM.II.G.K5 | Combustion heater and system component(s) function, operation, and inspection procedures. |
| AM.II.G.K6 | Vapor-cycle system and system component(s) operation, servicing, and inspection procedures. |
| AM.II.G.K7 | Air-cycle system and system component(s) operation and inspection procedures. |
| AM.II.G.K8 | Cabin pressurization and system component(s) operation and inspection procedures. |
| AM.II.G.K9 | Types of oxygen systems and oxygen system component(s) operation (e.g., chemical generator, pressure cylinder). |
| AM.II.G.K10 | Oxygen system maintenance and inspection procedures. |
Source: FAA-S-ACS-1, area AM.II.G, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 6 risk management and 15 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many environmental systems questions will I get?
The FAA gives this area 5-10% of the AMA test. On 100 questions that is about 5 to 10 (our arithmetic on the FAA range). Rivetry has 46 reviewed items tagged AM.II.G, 5 of them free.
How should I study environmental systems?
- An exhaust heat exchanger can leak carbon monoxide into the cabin. Know how it is inspected (K4).
- In a vapor-cycle system the refrigerant changes state in the evaporator and condenser. Refrigerant is recovered, never vented (K6, R2).
- An air-cycle machine cools bleed air by expanding it through a turbine (K7).
- Use only aviator's breathing oxygen, keep oil and grease away from fittings, and handle chemical oxygen generators with care because they get very hot (K9, K10, R3).
Learn it from FAA-H-8083-31B, then test yourself.
What could the practical ask me to do?
These are the 15 skill elements the ACS lists for AM.II.G. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Inspect an oxygen system.
- S2 Purge an oxygen system prior to servicing.
- S3 Service an oxygen system.
- S4 Clean and inspect a pilot emergency oxygen mask and supply hoses.
- S5 Inspect an oxygen system pressure regulator.
- S6 Inspect an oxygen system cylinder for serviceability.
- S7 Inspect a chemical oxygen generator for serviceability and safe handling.
- S8 Locate the procedures to troubleshoot a combustion heater.
- S9 Locate the procedures for servicing a refrigerant (vapor-cycle) system.
- S10 Inspect a combustion heater fuel system for leaks.
- S11 Locate the troubleshooting procedures for an air-cycle system.
- S12 Troubleshoot an air-cycle air conditioning system.
- S13 Inspect a cabin heater system equipped with an exhaust heat exchanger for cracks.
- S14 Clean and inspect an outflow valve for a pressurization system.
- S15 Locate troubleshooting procedures for a pressurization system.
The risk management elements for this area: Oxygen system maintenance (R1); Recovery of vapor-cycle refrigerant (R2); Handling or performing maintenance on, chemical oxygen generating systems (R3); Storage, handling, and use of compressed gas cylinder and high pressure systems (R4); Manufacturer's recommended servicing procedures, including refrigerant types (R5); Maintenance of combustion heaters (R6).
Free mini quiz: 5 practice questions
5 AM.II.G questions: 5 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.II.G.K1 a3-040
Under 14 CFR 25.841, a transport-category pressurization system must provide a cabin pressure altitude of no more than what value at the airplane's maximum operating altitude under normal conditions?
- 12,500 feet
- 10,000 feet
- 8,000 feet
Show answer
Answer: C. 14 CFR 25.841(a) requires a cabin pressure altitude of not more than 8,000 feet at the airplane's maximum operating altitude under normal operating conditions. 10,000 and 12,500 feet are often confused with altitudes in the operating rules for supplemental oxygen, not the pressurization design standard.
Source: 14 CFR 25.841; FAA-H-8083-31B, Cabin Environmental Control Systems / pressurization
AM.II.G.K2 a3-041
In a turbine aircraft that heats the cabin with compressor bleed air, how is the temperature of the delivered air controlled?
- A mixing valve blends hot bleed air with cooler air as commanded
- Engine power is adjusted to change the bleed air temperature
- A combustion heater adds heat when the bleed air is too cool
Show answer
Answer: A. Compressor bleed air is much hotter than the cabin needs, so a temperature control or mixing valve proportions hot bleed air with cooler air in response to the temperature selector and duct sensors. Engine power is set for flight needs, not for cabin temperature.
Source: FAA-H-8083-31B, Cabin Environmental Control Systems / bleed air heating
AM.II.G.K2 a3-042
Why can compressor bleed air be ducted into the cabin for heat, while engine exhaust gas never is?
- Bleed air is much cooler than exhaust gas, so it holds less carbon monoxide
- Bleed air is tapped before combustion, so it has no combustion products
- Bleed air passes through a catalytic filter that removes carbon monoxide
Show answer
Answer: B. Bleed air is tapped from the compressor ahead of the combustion section, so it is clean air that has only been heated by compression. Exhaust contains carbon monoxide at any temperature, which is why exhaust heat is only used through a sealed heat exchanger.
Source: FAA-H-8083-31B, Cabin Environmental Control Systems / bleed air heating
AM.II.G.K3 a3-043
Why do many aircraft use fans or ram-air ducts to move air around the instrument panel and avionics equipment?
- Moving air keeps the gyro rotors turning at their rated speed
- Electronic components fail sooner when their heat is not carried away
- Airflow keeps static charges from building on the display screens
Show answer
Answer: B. Avionics and electronic displays generate heat, and their reliability falls as internal temperatures rise, so cooling air is supplied by fans, ram air or equipment cooling systems. Gyro rotor speed is set by the vacuum or electrical drive, not by panel airflow.
Source: FAA-H-8083-31B, Cabin Environmental Control Systems / instrument and avionics cooling
AM.II.G.K1 a3-039
A pressurized airplane cruises at 35,000 feet with an 8,000-foot cabin altitude. Using 3.5 psi for outside pressure and 10.9 psi for the pressure at 8,000 feet, what is the cabin pressure differential?
- 11.2 psi
- 14.4 psi
- 7.4 psi
Show answer
Answer: C. Differential = cabin pressure - outside pressure = 10.9 - 3.5 = 7.4 psi. 11.2 psi comes from subtracting outside pressure from sea-level pressure (14.7 - 3.5), and 14.4 psi from adding the two pressures instead of subtracting.
Source: FAA-H-8083-31B, Cabin Environmental Control Systems / pressurization terms
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- What controls cabin pressure?
- The outflow valve, positioned by the pressure controller, sets how much air leaves the cabin (K8).
- Does the refrigerant type matter?
- Yes. Use the refrigerant the manufacturer specifies; servicing procedures and refrigerant types are risk element R5.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many environmental systems questions does Rivetry have?
- 46 reviewed items, 5 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-31B, Aviation Maintenance Technician Handbook: Airframe. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.