A&P inspection concepts and techniques practice questions

Inspection Concepts and Techniques is ACS area AM.I.K of the FAA General (AMG) test, 5-10% of its 60 questions, so roughly 3 to 6 questions (FAA-G-ACS-1, chapter 3). The ACS lists 5 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.I.K.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.

Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.

What does the ACS list for inspection concepts and techniques?

Inspection concepts and techniques covers precision measuring tools, calibration, nondestructive testing and the inspection programs a mechanic works under. It has only five knowledge elements, but NDT alone spans visual, dye penetrant, magnetic particle, eddy current, ultrasonic and radiographic methods.

CodeKnowledge element
AM.I.K.K1Measuring tools, including calipers, micrometers, and gauges.
AM.I.K.K2Calibration and tool accuracy requirements.
AM.I.K.K3Nondestructive Testing (NDT) procedures and methods.
AM.I.K.K4Aircraft inspection programs (e.g., progressive, 100-hour, annual, and other FAA-approved inspections).
AM.I.K.K5Aircraft inspection methods and tools for materials, hardware, and processes.

Source: FAA-S-ACS-1, area AM.I.K, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 5 risk management and 8 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).

How many inspection concepts and techniques questions will I get?

The FAA gives this area 5-10% of the AMG test. On 60 questions that is about 3 to 6 (our arithmetic on the FAA range). Rivetry has 42 reviewed items tagged AM.I.K, 5 of them free.

How should I study inspection concepts and techniques?

Learn it from FAA-H-8083-30B, then test yourself.

What could the practical ask me to do?

These are the 8 skill elements the ACS lists for AM.I.K. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).

The risk management elements for this area: Demagnetizing a component following a magnetic particle inspection (R1); Using precision measuring instruments (R2); Calibration of precision measuring equipment (R3); Selection of inspection techniques (R4); Damage prevention to aircraft components and test equipment when using an ohmmeter (R5).

Free mini quiz: 5 practice questions

5 AM.I.K questions: 5 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.

  1. AM.I.K.K1 g4-068

    On a vernier micrometer, the sleeve shows the 0.2 line plus three small lines, the thimble's 13 line is at the index, and vernier line 4 coincides with a thimble line. What is the reading?

    1. 0.2920 in
    2. 0.2134 in
    3. 0.2884 in
    Show answer

    Answer: C. Sleeve: 0.200 + 3 x 0.025 = 0.275. Thimble: 0.013, giving 0.288. Vernier: 4 x 0.0001 = 0.0004, total 0.2884 in. Reading the vernier as 0.004 gives 0.2920, and skipping the small sleeve lines gives 0.2134.

    Source: FAA-H-8083-30B, Hand Tools and Measuring Devices

  2. AM.I.K.K1 g4-069

    A mechanic must measure the inside diameter of a 2-in bushing bore using an outside micrometer. Which tool is used to transfer the measurement?

    1. A small-hole gauge
    2. A thickness (feeler) gauge
    3. A telescoping gauge
    Show answer

    Answer: C. A telescoping gauge expands to contact the bore, is locked, removed, and measured across with an outside micrometer. Small-hole gauges serve the same purpose but for holes too small for telescoping gauges, and a feeler gauge measures clearances, not bore diameters.

    Source: FAA-H-8083-30B, Hand Tools and Measuring Devices

  3. AM.I.K.K1 g4-070

    How should the zero setting of a 1-to-2-in outside micrometer be checked before use?

    1. By closing the spindle onto the anvil and reading zero
    2. By measuring a 1-in standard and confirming it reads 1.000 in
    3. By comparing a reading against a steel machinist's scale
    Show answer

    Answer: B. A 1-to-2-in micrometer cannot close to zero, so its accuracy is checked with a 1-in standard (gauge rod) that should read exactly 1.000 in. Closing spindle to anvil applies only to a 0-to-1-in micrometer, and a scale is far less precise than the micrometer.

    Source: FAA-H-8083-30B, Hand Tools and Measuring Devices

    Get Rivetry on Google Play

  4. AM.I.K.K1 g4-071

    Why does a micrometer have a ratchet stop or friction thimble?

    1. So the reading is locked in place after the tool is removed from the part
    2. So the reading is corrected for the part's temperature during measurement
    3. So the same light measuring force is applied for each reading
    Show answer

    Answer: C. The ratchet or friction thimble slips at a set force, so the spindle contacts the part with the same pressure each time and readings repeat. Locking the reading is the job of the spindle lock, and no part of the micrometer corrects for temperature.

    Source: FAA-H-8083-30B, Hand Tools and Measuring Devices

  5. AM.I.K.K1 g4-067

    A vernier caliper's main beam is graduated in 0.025-in divisions with a 25-division vernier. The vernier zero is just past the 1.425-in mark, and the 12th vernier line aligns with a beam line. What is the reading?

    1. 1.437 in
    2. 1.462 in
    3. 1.545 in
    Show answer

    Answer: A. Each vernier division adds 0.001 in: 1.425 + 0.012 = 1.437 in. Adding 0.012 to the next beam mark (1.450) gives 1.462, and reading the vernier as hundredths (1.425 + 0.12) gives 1.545.

    Source: FAA-H-8083-30B, Hand Tools and Measuring Devices

Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.

Get Rivetry on Google Play

More questions

How do I check a composite for delamination?
The tap test is the basic method and a skill element here (S8). Ultrasonic methods find more.
Do precision tools need calibration?
Yes. K2 covers calibration and tool accuracy requirements, and R3 the risk of using equipment that is out of calibration.
Are these the real FAA questions?
No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
How many inspection concepts and techniques questions does Rivetry have?
42 reviewed items, 5 of them free.

Sources

Related guides

General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.