A&P cleaning and corrosion control practice questions
Cleaning and Corrosion Control is ACS area AM.I.G of the FAA General (AMG) test, 5-10% of its 60 questions, so roughly 3 to 6 questions (FAA-G-ACS-1, chapter 3). The ACS lists 24 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.I.G.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for cleaning and corrosion control?
Cleaning and corrosion control has one of the longest lists in the ACS (24 knowledge elements): why metal corrodes, where it hides, how to remove and treat it, and how primers, topcoats and finishes go on. It also covers registration marks and refinishing control surfaces.
| Code | Knowledge element |
|---|---|
| AM.I.G.K1 | Aircraft cleaning procedures. |
| AM.I.G.K2 | Corrosion theory and causation. |
| AM.I.G.K3 | Types and effects of corrosion. |
| AM.I.G.K4 | Corrosion-prone areas in aircraft. |
| AM.I.G.K5 | Corrosion preventive maintenance procedures. |
| AM.I.G.K6 | Corrosion identification and inspection. |
| AM.I.G.K7 | Corrosion removal and treatment procedures. |
| AM.I.G.K8 | Corrosion preventive compounds (CPC) (e.g., waxy sealants, thin-film dielectrics). |
| AM.I.G.K9 | Selection of optimal CPC and frequency of treatment. |
| AM.I.G.K10 | Use of high-pressure application equipment. |
| AM.I.G.K11 | Improper use of cleaners on aluminum or composite materials. |
| AM.I.G.K12 | Dissimilar metals causing accelerated corrosion and role of protective barriers to mitigate this risk. |
| AM.I.G.K13 | Conversion coatings. |
| AM.I.G.K14 | Materials used for protection of airframe structures. |
| AM.I.G.K15 | Primer materials. |
| AM.I.G.K16 | Topcoat materials. |
| AM.I.G.K17 | Surface preparation for a desired finishing material. |
| AM.I.G.K18 | Effects of ambient conditions on finishing materials. |
| AM.I.G.K19 | Effects of improper surface preparation on finishing materials. |
| AM.I.G.K20 | Regulatory requirements for replacing identification, registration markings, and placards. |
| AM.I.G.K21 | Inspection of aircraft finishes. |
| AM.I.G.K22 | Safety practices/precautions when using finishing materials (e.g., PPE, fire prevention). |
| AM.I.G.K23 | Finishing materials application techniques and practices. |
| AM.I.G.K24 | Control surface balance considerations after refinishing. |
Source: FAA-S-ACS-1, area AM.I.G, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 8 risk management and 14 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many cleaning and corrosion control questions will I get?
The FAA gives this area 5-10% of the AMG test. On 60 questions that is about 3 to 6 (our arithmetic on the FAA range). Rivetry has 42 reviewed items tagged AM.I.G, 5 of them free.
How should I study cleaning and corrosion control?
- Learn corrosion as a cell: an anode, a cathode, an electrolyte and a path for electrons. Take away any one and the corrosion stops (K2).
- Match each corrosion type to where it shows up: pitting, intergranular, exfoliation, filiform, galvanic (dissimilar metals), fretting and stress corrosion (K3, K4).
- Know the treatment sequence: remove the corrosion completely, check the remaining material against the damage limits, then restore protection with a conversion coating, primer and topcoat (K7, K13 to K16).
- After refinishing a control surface, check its balance. Paint adds weight behind the hinge line (K24).
Learn it from FAA-H-8083-30B, then test yourself.
What could the practical ask me to do?
These are the 14 skill elements the ACS lists for AM.I.G. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Perform a portion of an aircraft corrosion inspection.
- S2 Identify, select, and use aircraft corrosion prevention/cleaning materials.
- S3 Apply corrosion prevention/coating materials.
- S4 Inspect finishes and identify defects.
- S5 Inspect an aircraft compartment for corrosion.
- S6 Identify procedures to clean and protect plastics.
- S7 Determine location and size requirements for aircraft registration numbers.
- S8 Prepare composite surface for painting.
- S9 Identify finishing materials and appropriate thinners.
- S10 Layout and mask a surface in preparation for painting.
- S11 Prepare metal surface for painting.
- S12 Determine what paint system can be used on a given aircraft.
- S13 Apply etch solution and conversion coating.
- S14 Identify types of protective finishes.
The risk management elements for this area: Health concerns when using paints, solvents, finishing materials, and processes (R1); Ventilation (R2); Identification of materials and processes to be used for cleaning or corrosion treatment on a given part or structure to prevent further damage (R3); SDS PPE instructions for products during removal and treatment of corrosion (R4); Working with flammable chemicals (R5); Disposal of chemicals and waste materials (R6); Use of PPE when working with paints and solvents (R7); Application of finishing materials (R8).
Free mini quiz: 5 practice questions
5 AM.I.G questions: 5 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.G.K2 g3-033
Electrochemical corrosion of an aluminum part requires an anode, a cathode, and a metallic path between them. What fourth condition must be present?
- A dissimilar metal fastener in contact with the part
- Cyclic stress in the part from flight or ground loads
- An electrolyte, such as water containing dissolved salts
Show answer
Answer: C. A corrosion cell needs an anode, a cathode, an electrolyte, and an electrical path; remove any one and corrosion stops, which is why keeping moisture out is so important. Dissimilar metals are not required, because differences within one alloy create anodic and cathodic areas.
Source: FAA-H-8083-30B, Cleaning and Corrosion / Corrosion theory
AM.I.G.K2 g3-034
In a corrosion cell on an aluminum skin, which area loses metal?
- The anodic area, where metal gives up electrons and goes into solution
- The cathodic area, where electrons are taken up from the electrolyte
- Both areas equally, because the same current passes through each
Show answer
Answer: A. Oxidation takes place at the anode, where metal atoms lose electrons and become ions in the electrolyte, so that is where metal is eaten away. The electrons travel through the metal to the cathode and are consumed there, which leaves the cathode undamaged.
Source: FAA-H-8083-30B, Cleaning and Corrosion / Corrosion theory; anodic and cathodic areas
AM.I.G.K3 g3-035
On an extruded aluminum spar cap, a mechanic finds surface layers lifting and flaking apart along the length of the part. What type of corrosion is this?
- Filiform corrosion
- Exfoliation corrosion
- Stress-corrosion cracking
Show answer
Answer: B. Exfoliation is an advanced form of intergranular corrosion along the elongated grain boundaries of extruded or rolled metal; corrosion products swell and push the layers apart. Filiform shows as worm-like tracks under paint, and stress-corrosion cracking appears as cracks, not lifted layers.
Source: FAA-H-8083-30B, Cleaning and Corrosion / Types of corrosion; exfoliation
AM.I.G.K1 g3-031
A parked airplane has a light coating of dust and airport film, but washing with water is not practical. Which cleaning method fits?
- Dry wash, using a spray-on cleaner wiped off with cloths
- Polishing with an abrasive compound to cut through the film
- A full solvent wipe of the painted surfaces with MEK
Show answer
Answer: A. Dry wash removes airport film, dust, and light soil when liquids are not practical; it is not meant for heavy deposits. Polishing is for restoring luster to dull or oxidized surfaces and removes finish, and MEK attacks many paints.
Source: FAA-H-8083-30B, Cleaning and Corrosion / Exterior cleaning; dry wash
AM.I.G.K1 g3-032
How should an acrylic windshield be cleaned?
- Wipe it dry first with a clean cloth to clear the dust, then apply the cleaner
- Flood it with water and mild soap, using a bare hand or soft cloth
- Wipe bug residue off with acetone or lacquer thinner, then polish it dry
Show answer
Answer: B. Flooding with water and mild soap floats grit away without scratching. Dry wiping drags abrasive dust across the plastic and builds static that attracts more. Acetone and similar solvents soften and craze acrylic.
Source: FAA-H-8083-30B, Cleaning and Corrosion / Cleaning transparent plastics
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Which metal corrodes when two different metals touch?
- The more anodic one in the galvanic series. A barrier such as primer, sealant or tape between the two reduces the effect (K12).
- Are registration marks really on the test?
- Yes. K20 covers the rules for replacing identification, registration markings and placards, and S7 asks for their location and size requirements, which are in 14 CFR part 45.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many cleaning and corrosion control questions does Rivetry have?
- 42 reviewed items, 5 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.