A&P ground operations and servicing practice questions
Ground Operations and Servicing is ACS area AM.I.F of the FAA General (AMG) test, 5-15% of its 60 questions, so roughly 3 to 9 questions (FAA-G-ACS-1, chapter 3). The ACS lists 16 knowledge elements for it (more counting sub-items), and your test report names any you miss by code, like AM.I.F.K1. Below are 5 sample original questions from Rivetry's reviewed bank, with the explanation for each.
Last updated · Published by Certloom Learning · How this page was made: written from the official sources listed at the end (read on 2026-11-14); the quiz items come from Rivetry's bank, where every item was solved blind by a second reviewer and disagreements were fixed or dropped.
What does the ACS list for ground operations and servicing?
Ground operations and servicing is the safety area of the General test: towing and tie-down, fueling, engine starts and run-ups, fire extinguishers, oxygen servicing, fuel grades and foreign object damage. Many questions turn on the one step you must not skip.
| Code | Knowledge element |
|---|---|
| AM.I.F.K1 | Aircraft towing procedures. |
| AM.I.F.K2 | Aircraft securing procedures. |
| AM.I.F.K3 | Aviation fueling/defueling procedures. |
| AM.I.F.K4 | Airport operation area procedures and ATC communications, including runway incursion prevention. |
| AM.I.F.K5 | Engine starting, ground operation, and aircraft taxiing procedures. |
| AM.I.F.K6 | Types/classes of fire extinguishers and procedures. |
| AM.I.F.K7 | Aircraft oil, hydraulic and pneumatic, and deicing servicing procedures. |
| AM.I.F.K8 | Oxygen system servicing procedures. |
| AM.I.F.K9 | Characteristics of aviation gasoline and turbine fuels, including basic types and means of identification. |
| AM.I.F.K10 | Fuel additives commonly used in the field. |
| AM.I.F.K11 | Use of approved grades/types of fuel in aircraft engines. |
| AM.I.F.K12 | Tool and hardware use and accountability. |
| AM.I.F.K13 | Material handling. |
| AM.I.F.K14 | Parts protections. |
| AM.I.F.K15 | Hazardous materials, Safety Data Sheets (SDS), and PPE. |
| AM.I.F.K16 | Foreign object damage effects. |
Source: FAA-S-ACS-1, area AM.I.F, read 2026-11-14. The written test draws on the knowledge elements. The ACS also lists 10 risk management and 12 skill elements, which the examiner checks at the oral and practical (The oral and practical (O&P) test).
How many ground operations and servicing questions will I get?
The FAA gives this area 5-15% of the AMG test. On 60 questions that is about 3 to 9 (our arithmetic on the FAA range). Rivetry has 42 reviewed items tagged AM.I.F, 5 of them free.
How should I study ground operations and servicing?
- Learn fuel identification. 100LL avgas is dyed blue, and Jet A is clear to straw colored. Misfueling is a named risk element (K9, R4).
- Know the fire classes and the extinguisher for each: Class A ordinary combustibles, Class B flammable liquids, Class C energized electrical equipment, Class D combustible metals (K6).
- Grounding during fueling, connecting external power and preparing to tow are all risk elements; learn the order of steps for each (R1 to R3).
- Oxygen servicing is a fire risk. Keep oil and grease away from oxygen fittings and equipment (K8, R5).
Learn it from FAA-H-8083-30B, then test yourself.
What could the practical ask me to do?
These are the 12 skill elements the ACS lists for AM.I.F. Any of them can become a project at the oral and practical, done with the references the examiner provides (Practical test projects by ACS area).
- S1 Perform a foreign object damage control procedure.
- S2 Connect external power to an aircraft.
- S3 Prepare an aircraft for towing.
- S4 Use appropriate hand signals for the movement of aircraft.
- S5 Inspect an aircraft fuel system for water and foreign object debris (FOD) contamination.
- S6 Identify different grades of aviation fuel.
- S7 Select an approved fuel for an aircraft.
- S8 Prepare an aircraft for fueling.
- S9 Follow a checklist to start up or shut down an aircraft reciprocating or turbine engine.
- S10 Identify procedures for extinguishing fires in an engine induction system.
- S11 Secure an aircraft.
- S12 Locate and explain procedures for securing a turbine-powered aircraft after engine shutdown.
The risk management elements for this area: Preparing to tow an aircraft (R1); Connecting external power equipment to an aircraft (R2); Fueling/defueling ungrounded aircraft or using improper equipment (R3); Misfueling and using incorrect or contaminated fuel (R4); Oxygen system servicing (R5); Engine start/run-up without using a checklist (R6); Engine starting and ground operations (R7); Engine starting and operation while troubleshooting or adjusting engine controls (R8); Ground operation of an aircraft engine with cowling removed contrary to manufacturer instructions (R9); Ground operation of aircraft in the vicinity of other aircraft or ground support equipment (R10).
Free mini quiz: 5 practice questions
5 AM.I.F questions: 5 from the app's free set and 0 more as a sample. These are original Rivetry items from the reviewed bank of 1,792, not FAA test questions. Open each one to check your answer.
AM.I.F.K1 g3-002
Before towing a nosewheel-steered airplane with a tow bar, a mechanic notices turn-limit marks on the nose gear. What do these marks indicate?
- The strut extension at which the nose gear is properly serviced for towing
- The maximum swivel angle; towing beyond it can damage the steering parts
- The straight-ahead alignment required before the tow bar is disconnected
Show answer
Answer: B. Turn-limit marks show how far the nose wheel may be swung by the tow bar. Turning past them can overstress or break steering stops, linkages, or torque links, which is why some types require disconnecting the steering before towing. The marks have nothing to do with strut servicing.
Source: FAA-H-8083-30B, Safety, Ground Operations, and Servicing / Aircraft towing; nose gear turning limits
AM.I.F.K2 g3-003
An airplane is tied down outdoors with manila rope just before rain is forecast. How should the tie-down ropes be adjusted?
- Pull them drum-tight, because manila rope stretches when it gets wet
- Replace them with chain, because wet manila loses nearly all its strength
- Leave some slack, because manila rope shrinks when it gets wet
Show answer
Answer: C. Manila fiber absorbs water and shrinks, so a rope tied tight can pull hard enough to damage tie-down rings or structure when it gets wet; a little slack is left for this. Wet manila does not stretch, and it does not lose nearly all its strength. Nylon or polyester rope does not shrink appreciably.
Source: FAA-H-8083-30B, Safety, Ground Operations, and Servicing / Securing aircraft; tie-down ropes
AM.I.F.K2 g3-004
Why are control locks (gust locks) installed when a light airplane is parked and tied down outside?
- To keep gusts from slamming the control surfaces against their stops
- To keep the airplane from weathervaning against its tie-down ropes in wind
- To keep unauthorized persons from starting the engine and taxiing away
Show answer
Answer: A. Unsecured control surfaces are driven back and forth by gusts, hammering hinges, cables, and stops. Locks do not restrain the airframe itself; tie-down ropes and chocks do that. They are not a theft or engine-start security device.
Source: FAA-H-8083-30B, Safety, Ground Operations, and Servicing / Securing aircraft; control locks
AM.I.F.K3 g3-005
During over-wing fueling, when should the bonding cable on the fuel nozzle be connected to the aircraft?
- As soon as fuel begins flowing into the tank
- Before the fuel tank cap is removed
- After the cap is removed but before flow starts
Show answer
Answer: B. The nozzle is bonded before the cap comes off so any static difference between nozzle and aircraft equalizes while no vapor is escaping. Connecting after the cap is removed means a spark could jump at the open filler, exactly where the vapor is richest.
Source: FAA-H-8083-30B, Safety, Ground Operations, and Servicing / Fueling procedures; grounding and bonding
AM.I.F.K1 g3-001
A crew is towing a light twin out of a crowded hangar with a tug, with a wing walker at each wingtip and a qualified person on the brakes. How fast should the aircraft be moved?
- No faster than the wing walkers can comfortably walk alongside
- At whatever speed the tug driver judges safe, since the brakes are manned
- At a steady 10 mph so the nose wheel tracks straight without shimmy
Show answer
Answer: A. Towing speed is limited to the walking pace of the team so the wing walkers can keep watch on clearances and signal a stop in time. Having someone on the brakes does not make a faster tow safe; a hard stop on the aircraft brakes can overload the tow bar and nose gear.
Source: FAA-H-8083-30B, Safety, Ground Operations, and Servicing / Aircraft towing
Rivetry has 1,792 items like these for the General, Airframe and Powerplant tests, timed tests at the FAA length, and a figure bench that works every calculation step by step. Try the sample questions or open the free bench.
More questions
- Are hand signals tested?
- Using hand signals for moving aircraft is a skill element (S4), so expect them at the practical and possibly in written questions.
- Does this area include runway incursions?
- Yes. K4 covers airport operations area procedures and ATC communications, including runway incursion prevention.
- Are these the real FAA questions?
- No. The FAA does not publish its live test questions. These are original practice items tagged with the ACS code they practice.
- How many ground operations and servicing questions does Rivetry have?
- 42 reviewed items, 5 of them free.
Sources
- FAA-S-ACS-1, Aviation Mechanic General, Airframe, and Powerplant Airman Certification Standards (November 1, 2021). FAA. Read 2026-11-14.
- FAA-G-ACS-1, Companion Guide to the Aviation Mechanic ACS (with Changes 1 and 2, September 2024). FAA. Read 2026-11-14.
- FAA-H-8083-30B, Aviation Maintenance Technician Handbook: General. FAA. Used to write the practice items 2026-11-14.
Related guides
General study information, not legal advice. Rules and FAA documents change; confirm with the FAA (faa.gov, your Flight Standards District Office) before you act.